Land Pride RC5610 Series Скачать руководство пользователя

Страница: 53 / 70

Section 5: Maintenance & Lubrication

RC5610, RC6610, RCM5610, & RCM6610 Series 2 S/N Rotary Cutters 330-539M

5/6/20

Table of Contents

Type A Clutch Assembly

Figure 5-13

Clutch Disassembly, Inspection & Assembly

Refer to Figure 5-13:

If clutch run-in procedure above indicated that one or more

friction disks did not slip, then the clutch must be

disassembled to separate the friction disks.

Disassembly

Disassembly of clutch is simply a matter of first removing

spring retainer nuts (#1), springs (#2), and bolts (#3) from

the assembly. Each friction disk (#4) must then be

separated from the metal surface adjacent to it.

Inspection

Inspect all parts for excessive wear and condition. Clean

all parts that do not require replacement.The original

friction disk thickness is 1/8" (3.2mm) and should be

replaced if thickness falls below 3/64" (1.1mm). If

clutches have been slipped to the point of “smoking”, the

friction disks may be damaged and should be replaced.

Heat build-up may also affect the yoke joints.

Assembly

Reassemble each friction disk (#4) next to the metal plate

it was separated from. Install bolts (#3) through end

plates and intermediate plates as shown. Place

springs (#2) over the bolts and secure with nuts (#1).

23554

IMPORTANT:

Not all clutches are assembled the

same with the same number of components. Be sure

to keep track of order and orientation of your clutch

components during disassembly.

Type A Clutch Spring Adjustment

Figure 5-14

Refer to Figure 5-14:

Progressively tighten each spring retainer bolt until

correct spring height “A” is reached.

Driveline

No.

Driveline
Location

Power

Take-Off

Speed

Cat
No.

A (inches)

Spring Height

826-818C

Center

540/1000

1.32"

826-811C

Wing

540/1000

1.32"

826-812C

Wing

540/1000

1.32"

24600

Содержание RC5610 Series







































































Результаты поиска

Содержание RC5610 Series

Отзывы:

Похожие инструкции для RC5610 Series

Бренды по названию

Популярные бренды

Land Pride RC5610 Series, Руководство оператора

Результаты поиска

Содержание RC5610 Series

Отзывы:

Похожие инструкции для RC5610 Series

Бренды по названию

Популярные бренды