Land Pride RC5610 Series, Руководство оператора

Страница: 38 / 70

Section 3: Operating Instructions
RC5610, RC6610, RCM5610, & RCM6610 Series 2 S/N Rotary Cutters 330-539M 5/6/20
34
Table of Contents
manual for acceptable inclines the tractor is capable of
traveling across.
•
Perform scheduled maintenance. Check for loose
hardware, missing parts, broken parts, structural cracks,
and excessive wear. Make repairs before putting the
implement back into service.
•
Never carry riders on the implement or tractor. Riders can
obstruct the operator’s view, interfere with controls, be
pinched by moving components, become entangled in
rotating components, struck by objects, thrown about, fall
off and be run over, etc.
•
Always follow “Tractor Shutdown Procedure” provided in
this manual before dismounting the tractor.
•
Do not raise the wing off the ground when traveling across
an incline. The weight of the wing will increase the risk of a
rollover.
•
Operate only power machines equipped with a certified
Roll-Over Protective Structure (ROPS) and seat belt. Keep
folding ROPS in the “locked up” position when
appropriate. If ROPS is in the locked up position, fasten seat
belt snugly and securely to help protect against serious
injury or death from falling and machine overturn.
•
Watch while making tight turns to ensure that the rear
tractor tires and lower 3-point arms do not make contact
with cutter hitch, driveline or deck. Keep lower 3-point
arms raised at all times when hitched to a pull-type cutter.
•
Wait for blades to come to a complete stop before accessing
blade bolts through blade bolt access hole.
•
Do not use implement to lift objects; to pull objects such as
fence posts, stumps, etc; or to push objects. The unit is not
designed or guarded for these uses.
•
Do not use implement to tow other equipment unless it is
designed with a tow hitch. Doing so can result in loss of
control and damage the equipment.
•
Do not operate a cutter with a hitch or hitch pin that is
excessively worn, bent, broken, or has structural cracks.
The hitch and/or hitch pin can break apart separating cutter
from tractor.
•
Avoid catching hydraulic hoses on brush, posts, tree limbs,
and other protrusions that could damage and/or break them.
•
Buildup of debris around moving components and
gearboxes is a fire hazard. Keep rotating parts and
gearboxes free from debris to avoid serious injury and
property damage.
•
Improper oil level can cause bearing failure and be a fire
hazard. Maintain proper gearbox oil level to avoid serious
injury and property damage.
•
Do not exceed rated cutting capacity of your cutter. See
specifications & capacities for specified cutting capacity.
Exceeding rated cutting capacity can damage drive
components, cutter blades, and deck components.
•
Do not operate a broken or bent driveline. Such a driveline
will break apart while rotating at high speeds and can cause
serious injury or death. Always remove the implement from
use until the damaged driveline can be repaired or replaced.
WARNING
!
To avoid serious injury or death:
Some tractors are equipped with two power take-off speeds.
Be certain your tractor’s power take-off is set-up to operate at
the implement’s rated power take-off speed or equipment
breakage may result. RC models are rated for 540 rpm and
RCM models are rated for 1000 rpm.
Tractor & Cutter Inspection
Make the following inspections with cutter attached to a
tractor and cutter parked on a level surface, power take-
off disengaged, and cutter blades stopped.
1. Inspect tractor safety equipment to make sure it is in
good working condition.
2. Inspect cutter safety equipment to make sure it is
installed and in good working condition.
3. Check driveline to make certain it is securely
connected to the tractor power take-off shaft and
cutter gearbox shaft. Also, make certain that the
guards are in good working condition and in place.
4. Check driveline hanger. Make sure it is rotated down
away from the driveline.
5. Remove 3-point lower arms or secure them in the
raised position so they do not interfere with driveline,
hoses, or hitch.
6. Check all hoses and wires to be sure that they will not
pinch or come in contact with rotating drivelines.
7. Start tractor and carefully raise and lower implement
to ensure tractor drawbar, tires, and other equipment
on the tractor do not contact cutter or driveline. See
also
“Driveline Clearance Check”
on page 24
8. Raise center deck fully up.
9. Without lowering implement, shut tractor down
properly. Refer to “Tractor Shutdown Procedure”
on page 16.
10. Place sturdy support blocks or jack stands under the
four center deck corners.
11. Start tractor and lower center deck down onto the
supports.
12. Shut tractor down properly before dismounting.
IMPORTANT:
Maintain correct power take-off speed.
Loss of power take-off speed will allow blades to
swing back and result in ragged, uneven cutting.
IMPORTANT: If wing driveline profile is bent or
twisted, disconnect that driveline from the wing
gearbox before folding the wing up. This will protect
both the wing and divider gearboxes. Repair
driveline before putting cutter back into service.