Land Pride RC5610 Series Скачать руководство пользователя

Страница: 48 / 70

Section 5: Maintenance & Lubrication

RC5610, RC6610, RCM5610, & RCM6610 Series 2 S/N Rotary Cutters 330-539M

5/6/20

Table of Contents

Skid Shoes & Side Skirt

WARNING

To avoid serious injury or death:
Excessive wear on skid shoes may cause inadequate operation

of cutter and create a safety hazard.

Two skid shoes are mounted on the center section and

one skid shoe mounted on the wing section. Check all

skid shoes for wear and replace if necessary. Order only

genuine Land Pride parts from your local Land Pride

dealer.

Center Skid Shoes

Refer to Figure 5-2 on page 44:

1. Remove 5/8" hex whiz nuts (#4), 5/8" hex bolts (#3)

and skid shoes (#1) from center deck (#2).

2. Attach new skid shoes (#1) to cutter with existing

5/8" hex bolts (#3) and secure with 5/8" hex whiz

nuts (#4). Tighten whiz nuts to the correct torque.

Wing Skid Shoe

Refer to Figure 5-3 on page 44:

1. Remove 3/8" whiz nuts (#5A), carriage bolts (#4),

and hardened skid shoe (#2) from the wing deck.

2. Remove 3/8" whiz nuts (#5), plow bolts (#3), and

wing skid shoe (#1) from the wing deck.

3. Discard worn skid shoe.
4. Inspect plow bolts for wear and replaced if needed.
5. Attach new hardened skid shoe (#2) to cutter side

panel with removed 3/8"-16 x 1 1/4" GR5 carriage

bolts (#4) and whiz nuts (#5A). Do not torque nuts

tight at this time.

6. Attach new skid shoe (#1) to cutter side panel with

new/existing 3/8" -16 x 1 1/4" GR5 plow bolts (#3)

and hex whiz nuts (#5).

7. Tighten whiz nuts (#5 & #5A) to the correct torque.

Wing Side Skirt With Skid Shoes

Refer to Figure 5-4 on page 44:

1. Remove existing hex whiz nuts (#3), carriage

bolts (#2), and side skirt (#1).

2. Attach new side skirt to cutter with 1/2" -13 x 1 1/4"

GR5 carriage bolts (#2). Secure with new 1/2" hex

whiz nuts (#3). Tighten nuts to the correct torque.

NOTE:

Side Skirt assembly part numbers includes

side skirt, skid shoes, decals & mounting hardware.

Center Skid Shoe

Figure 5-2

Wing Skid Shoes

Figure 5-3

Wing Side Skirt With Skid Shoes

Figure 5-4

# Part No. Description

1 330-185H CENTER SKID SHOE

30280

37641

# Part No. Description

1 330-835D WING SKID SHOE
2 331-120H HARDENED WING SKID SHOE
3 802-466C PLOW BOLT, 3/8" - 16 x 1 1/4" grade 5

# Part No. Description

1 See Parts Manual for Part Numbers and color options.

37642

Содержание RC5610 Series







































































Результаты поиска

Содержание RC5610 Series

Отзывы:

Похожие инструкции для RC5610 Series

Бренды по названию

Популярные бренды

Land Pride RC5610 Series, Руководство оператора

Результаты поиска

Содержание RC5610 Series

Отзывы:

Похожие инструкции для RC5610 Series

Бренды по названию

Популярные бренды