Land Pride RC5610 Series Скачать руководство пользователя страница 42

Страница: 42 / 70

Section 3: Operating Instructions

RC5610, RC6610, RCM5610, & RCM6610 Series 2 S/N Rotary Cutters 330-539M

5/6/20

Table of Contents

Engage Blades

1. Select a gear range that will allow cutter to make a

smooth cut without lugging the tractor down. See

“Select Gear Range”

above for instructions.

2. With wing lowered, increase throttle to a speed just

enough to get the cutter started without stalling

tractor while slowly engaging power take-off. Use

tractor’s power take-off soft start option if available.

3. Ensure all power shafts are rotating and cutter is not

vibrating excessively after ramping up to full power

take-off speed for at least 3 seconds. If excessive

vibration continues after 3 seconds at full power take-

off speed, disengage power take-off immediately,

shut down tractor, and remove switch key. Wait for

blades to come to a complete stop before

dismounting tractor.

4. Investigate the cause if cutter was shut down due to

excessive vibration. See

“Blade Operation

Inspection”

on page 35 for detailed instructions.

5. If cutter was not shut down, commence forward

cutting operation at full power take-off operating

speed. Make a new gear selection if tractor is lugging

down or if cutter is making a rough cut.

6. Periodically, shut tractor down properly and dismount

to do an inspection. Refer to

“Tractor Shutdown

Procedure”

on page 16.

Dismount tractor and check for objects wrapped

around blade spindles. Block deck up before

removing objects.

8. Frequently inspect cutter for loose bolts and nuts.

Tighten all loose hardware as indicated in the

“Torque Values Chart”

on page 64.

Disengage Blades

1. Slowly decrease throttle speed until engine idle

speed is reached.

2. Disengage power take-off.
3. Stay on the tractor until the blades have come to a

complete stop. Always place tractor in park or set

park brake, shut tractor engine off, and remove

switch key before dismounting.

IMPORTANT:

Cutter blades can lock-up against

each other during start-up and shut-down,

especially if tractor’s power take-off engagement is

“INSTANT ON” and/or “INSTANT OFF”. Follow Blade

Engagement and Blade Disengagement instructions

to help eliminate blade lock up.

Содержание RC5610 Series







































































Результаты поиска

Содержание RC5610 Series

Отзывы:

Бренды по названию

Популярные бренды

Land Pride RC5610 Series, Руководство оператора

Результаты поиска

Содержание RC5610 Series

Отзывы:

Бренды по названию

Популярные бренды