Land Pride RC5610 Series Скачать руководство пользователя

Страница: 26 / 70

Section 1: Assembly & Set-up

RC5610, RC6610, RCM5610, & RCM6610 Series 2 S/N Rotary Cutters 330-539M

5/6/20

Table of Contents

Driveline Assembly

DANGER

To avoid serious injury or death:
Make certain driveline yokes are securely fastened at each

end. A loose yoke can work free allowing the driveline to

rotate uncontrollably causing implement damage and bodily

injury or death to anyone nearby.

The main driveline can be constant velocity or

conventional type. A pull-collar is used to secure the

driveline to the tractor power take-off shaft.

Remove Main Driveline from Cutter

Figure 1-17

IMPORTANT:

The driveline must be lubricated

before putting it into service. Refer to

“Lubrication

Points”

on page 52.

NOTE:

Complete

“Unfold Wing”

on page 21 before

removing driveline from its shipping location.

37810

Refer to Figure 1-17:

1. Remove hex whiz nuts (#4A), carriage bolts (#3), and

shipping bracket (#2). Discard shipping bracket.

2. Slide driveline (#5) off end of shipping bracket (#1).

Set driveline aside for attaching to splitter box later.

3. Reinsert carriage bolts (#3) and secure with hex whiz

nuts (#4A). Tighten whiz nuts to the correct torque.

4. Remove hex whiz nuts (#4B), carriage bolts (#3), and

shipping bracket (#1). Discard shipping bracket.

5. Reinsert carriage bolts (#3) and secure with hex whiz

nuts (#4B). Tighten whiz nuts to the correct torque.

Refer to Figure 1-16:

6. Unsnap latches (#5) on both sides of gearbox

shield (#10) and remove shield.

Remove and discard rubber shaft protector (#7) from

splitter gearbox shaft (#8).

8. Remove locknuts (#1) and bolts (#2) from bolted

coupler end of driveline (#9).

9. Insert bolted coupler end of driveline (#9) through

gearbox shield (#10) and attach to gearbox input

shaft (#8) with removed bolts (#2) and locknuts (#1).

Tighten locknuts to the correct torque.

10. Collapse driveline (#9) by pushing tractor end of

driveline toward splitter gearbox (#8).

11. Rotate driveline hanger (#11) up and support

driveline (#9) on hanger. Final adjustments to hanger

will be made later after tractor hook-up.

12. Return gearbox shield (#10) to mounting plate (#4)

and secure with latches (#5).

13. Check safety chain (#3). Make sure it is latched to

mounting plate (#4) and gearbox shield (#10).

Driveline Assembly

Figure 1-16

37619

Содержание RC5610 Series







































































Результаты поиска

Содержание RC5610 Series

Отзывы:

Похожие инструкции для RC5610 Series

Бренды по названию

Популярные бренды

Land Pride RC5610 Series, Руководство оператора

Результаты поиска

Содержание RC5610 Series

Отзывы:

Похожие инструкции для RC5610 Series

Бренды по названию

Популярные бренды