manualshive.com logo in svg

Land Pride Post Hole Diggers HD25, Руководство оператора

Поделиться
Скачать
Land Pride Post Hole Diggers HD25 Скачать руководство пользователя страница 3

Table of Contents

7/31/17

© 

Copyright 2017 All rights Reserved

Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the
preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use
of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this
product at the time of its publication, and may not reflect the product in the future. 

Land Pride is a registered trademark.

All other brands and product names are trademarks or registered trademarks of their respective holders.

Printed in the United States of America.

HD25 and HD35 Hydraulic Post Hole Diggers 317-076M

Table of Contents

Important Safety Information   . . . . . . . . . . . . .  1

Safety at All Times   . . . . . . . . . . . . . . . . . . . . . . . . . 1
Look For The Safety Alert Symbol   . . . . . . . . . . . . . 1
Safety Labels   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Introduction  . . . . . . . . . . . . . . . . . . . . . . . . . . .  7

Application   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Using This Manual   . . . . . . . . . . . . . . . . . . . . . . . . . 7
Owner Assistance  . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Serial Number   . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Further Assistance  . . . . . . . . . . . . . . . . . . . . . . . . 8

Section 1: Assembly & Set-up   . . . . . . . . . . . .  9

Skid Steer/Tractor Requirements   . . . . . . . . . . . . . . 9
HD 3-Point Mount Assembly  . . . . . . . . . . . . . . . . . . 9
HD Bucket Mount Assembly  . . . . . . . . . . . . . . . . . 10
Skid/Loader Mount Assembly  . . . . . . . . . . . . . . . . 11

Center Mount & Offset Mount   . . . . . . . . . . . . . . 11

Skid/Loader Hose Assembly  . . . . . . . . . . . . . . . . . 12

Center/Offset Mount for Tractors  . . . . . . . . . . . . 12
Center/Offset Mount for Skid Steers   . . . . . . . . . 12

Hooking Up 3-Point Mount   . . . . . . . . . . . . . . . . . . 12
Unhooking 3-Point Mount  . . . . . . . . . . . . . . . . . . . 13
Hooking Up Bucket Mount   . . . . . . . . . . . . . . . . . . 14
Unhooking Bucket Mount   . . . . . . . . . . . . . . . . . . . 14
Hooking Up Skid/Loader Mount   . . . . . . . . . . . . . . 15
Unhooking Skid/Loader Mount   . . . . . . . . . . . . . . . 15
Auger Assembly   . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Hydraulic Hook-Up to Tractor  . . . . . . . . . . . . . . . . 16
Hydraulic Hook-Up to Skid Steer . . . . . . . . . . . . . . 17

Section 2: Adjustments  . . . . . . . . . . . . . . . . .  18

Post Hole Digging Depth  . . . . . . . . . . . . . . . . . . . . 18

Section 3: Operating Instructions   . . . . . . . .  19

Operator’s Responsibilities  . . . . . . . . . . . . . . . . . . 19
Safety Information  . . . . . . . . . . . . . . . . . . . . . . . . . 19
Dual-Angle Teeth   . . . . . . . . . . . . . . . . . . . . . . . . . 20
Transport With Post Hole Digger . . . . . . . . . . . . . . 21
Operating Instructions  . . . . . . . . . . . . . . . . . . . . . . 21
General Operation   . . . . . . . . . . . . . . . . . . . . . . . . 22

Section 4: Options   . . . . . . . . . . . . . . . . . . . . . 23

Auger Extensions (Option)   . . . . . . . . . . . . . . . . . . 23
Dirt Augers (Option)   . . . . . . . . . . . . . . . . . . . . . . . 23
Tree Augers (Option) . . . . . . . . . . . . . . . . . . . . . . . 23
Dirt & Tree Auger Teeth   . . . . . . . . . . . . . . . . . . . . 23
Rock Augers (Option)   . . . . . . . . . . . . . . . . . . . . . . 24
Bolt-on Rock Heads (Accessory) . . . . . . . . . . . . . . 24
Rock Auger Teeth  . . . . . . . . . . . . . . . . . . . . . . . . . 24
HD25/35 3-Point Down Pressure Kit  . . . . . . . . . . . 25
Down Pressure Kit Assembly   . . . . . . . . . . . . . . . . 25
Adjust Down Pressure Kit  . . . . . . . . . . . . . . . . . . . 27
HD25 & HD35 Storage Stand   . . . . . . . . . . . . . . . . 28
HD 3-Point Mount Assembly  . . . . . . . . . . . . . . . . . 30
HD Bucket Mount Assembly   . . . . . . . . . . . . . . . . . 30
Tractor Front Loader Mount . . . . . . . . . . . . . . . . . . 30
Skid Steers/Track Loader Mount  . . . . . . . . . . . . . . 31
HD25/35 QA Mount (Accessory)  . . . . . . . . . . . . . . 31

Section 5: Maintenance & Lubrication   . . . . . 32

General Maintenance Information  . . . . . . . . . . . . . 32
Safety Information  . . . . . . . . . . . . . . . . . . . . . . . . . 32
Daily Inspections  . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Long-Term Storage  . . . . . . . . . . . . . . . . . . . . . . . . 32
Ordering Replacement Parts  . . . . . . . . . . . . . . . . . 33
Lubrication Points  . . . . . . . . . . . . . . . . . . . . . . . . . 33

Gearbox Input and Output Shafts  . . . . . . . . . . . . 33
Gear Lube Fluid Level   . . . . . . . . . . . . . . . . . . . . 33

Section 6: Specifications & Capacities  . . . . . 34
Section 7: Features & Benefits   . . . . . . . . . . . 37
Section 8: Troubleshooting  . . . . . . . . . . . . . . 38
Section 9: Torque Values Chart . . . . . . . . . . . 40
Section 10: Warranty   . . . . . . . . . . . . . . . . . . . 41

Содержание Post Hole Diggers HD25















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды