Land Pride NTS2607 Скачать руководство пользователя

Страница: 23 / 78

Section 1: Assembly & Set-up

NTS2607, NTS2609, & NTS2611 No-Till Seeder 329-141M

Table of Contents

9/10/20

Purge Hydraulic System

DANGER

To avoid serious injury or death:

•

Never remove or install a hydraulic cylinder with

hydraulics to the cylinders under pressure. The seeder will

drop suddenly. Also, air trapped in a new or repaired

cylinder can drop the seeder suddenly when raising and

lowering the unit. Either situation can damage to the seeder

and cause serious bodily injury or death.

•

Do not use a park jack to support the seeder during purging

operations. The seeder can fall while purging the hydraulic

system. Instead, hook seeder to a tractor drawbar to help

stabilize the unit while purging the hydraulic system.

•

Make sure implement is lowered to the ground and all

hydraulic pressure is relieved before hooking-up or

disconnecting any hydraulic lines, fittings, or cylinders.

1. Hook seeder to the tractor drawbar. Refer to steps 1-

13 under

“Hook-up Pull-Type Seeder”

on page 24.

Do not attach hydraulic hoses to the tractor duplex at

this time.

2. Remove park jack and store it on the seeder frame.

Refer to

“Store Park Jack”

on page 25.

3. With barrel end of all three hydraulic cylinders pinned

to their respective mounting lugs and all hydraulic

fittings are tight, unpin cylinder rods from their

mounting lugs.

4. Tip rod end of all three hydraulic cylinders up as

much as possible and in some fashion hold cylinders

in this position without restricting rod movement.

5. Attach hydraulic hoses to the tractor duplex outlet

with float capabilities.

6. With tractor started, engage hydraulics until the

hydraulic cylinder at the front of the seeder is fully

extended.

Disengage hydraulics, and wait one minute. This will

allow any trapped air to migrate toward the

re-phasing port.

8. Repeat steps 6 & 7 for each of the two remaining

hydraulic cylinders.

9. Engage hydraulics again and hold engaged for two

full minutes.

IMPORTANT:

Be sure tractor reservoir is filled

properly before operating hydraulic cylinders. If

tractor reservoir is low on hydraulic fluid, there is a

chance of drawing air into the system causing jerky

or uneven cylinder movements.

IMPORTANT:

Attach hydraulic hoses only to tractor

hydraulics with float capabilities.

Tractor hydraulics

for the seeder must be locked in float position

while lowering the seeder and while seeding,

otherwise the seeder can be damaged.

10. After two minutes have passed, cycle hydraulic

cylinders by fully retracting and extending them. End

with cylinder rods fully extended.

11. Shut tractor engine off and remove switch key.
12. Remove supports holding cylinder rods in the tipped

up position.

13. Return to the tractor and retract cylinders slowly until

cylinder rod clevises align with mounting lugs.

14. Shut tractor engine off and remove switch key.
15. Pin cylinder rods to their respective mounting lugs.
16. When all three rod ends are pinned securely, restart

tractor and engage hydraulics to lift seeder until

cylinder rods are full extended. Hold tractor lever in

the engaged position for one minute.

17. With cylinders fully extended, shut tractor engine off

and remove switch key.

18. Check and refill tractor hydraulic reservoir if needed.

Содержание NTS2607















































































Результаты поиска

Содержание NTS2607

Отзывы:

Похожие инструкции для NTS2607

Бренды по названию

Популярные бренды

Land Pride NTS2607, Руководство оператора

Результаты поиска

Содержание NTS2607

Отзывы:

Похожие инструкции для NTS2607

Бренды по названию

Популярные бренды