Land Pride NTS2607 Скачать руководство пользователя

Страница: 39 / 78

Section 2: Operating Instructions

NTS2607, NTS2609, & NTS2611 No-Till Seeder 329-141M

Table of Contents

9/10/20

General Operating Instructions

Once you have read the Operator’s Manual, properly

attached the seeder to the tractor, ran through the

Operating Checklist, filled the box with seed, and

calibrated the unit for proper seed rate delivery, it’s time

to do some serious seeding.

Tow Package Only:

Make sure hydraulic hoses are

attached to the tractor duplex outlet with factory float.

Place control lever to raise and lower the seeder in float

position while lowering the seeder and seeding seeds.
The power to drive the NTS Seeder comes from the

forward momentum of the tractor. Lock in/out drive

systems transfers that power from the ground driven rear

packer assembly to the various seedboxes through chain

driven sprockets and the grass seeds transmission. The

seed rate remains constant in direct proportion to the

distance traveled and is affected very little by actual

ground speed.
There are holes on the side of the chain drive guards for

accessing the lock in/out pins for the All Seeds Drive

System, Small Seeds Drive, and Native Seeds Drive. The

Grass Seeds Drive System uses a transmission to select

a speed range. Set the transmission in neutral to lock out

its drive system. You should lock out the All Seeds Drive

System and any seedbox that is not being used before

transporting your NTS Seeder.
To disengage the small seeds and/or grass seeds drive

system, pull out on the system lock in/out pin and rotate it

one-quarter of a turn in either direction. To engage their

drive systems, rotate the lock in/out pin until you can feel

it pop in. Do not pull out on the pin while engaging it.
You should always engage the All Seeds Drive System

when ready to start seeding. At the same time, you

should check the various seedbox drive systems to make

sure the seedboxes in use are engaged and the

seedboxes not in use are disengaged.
The front spiked rollers open up the soil profile as they

pass over areas to be seeded. The more the front rollers

are angled, the more aggressive the cultivating action will

be. Seed is then delivered at the precise predetermined

rate through the wind guarded seed drop area between

the front and rear rollers. The rear roller then presses

seed into firm contact with the soil to promote a superbly

high germination rate. Seeding should not be attempted

in wet or muddy conditions.
Now that you understand how it works, it is time to begin

seeding. You may want to make a few passes with the All

Seeds Drive System locked out just to make sure your

front rollers are adjusted to the proper angle, and to

determine correct ground speed for cultivating the soil

profile to your expectations. Ridging of loose soil is

possible when the front rollers are set at an angle and

your ground speed is too fast. Slow your ground speed to

eliminate ridging. Re-engage the All Seeds Drive System

once you are satisfied that the proper amount of soil

opening action is being achieved.
You should already have removed any large stones or

obstacles from the area you plan to seed. Line the tractor

up for the first pass and choose a tractor gear selection

that will deliver a ground speed of approximately

3-5 mph. Lower the seeder slowly to the ground and

begin driving forward, slowly at first until you get

comfortable with what you are doing. As you approach

the end of the pass you are seeding, slow down and

come to a stop while simultaneously raising the seeder

off of the ground. With the seeder raised, line up for your

next pass and repeat the process. Finish seeding by

making back and forth passes across the turnaround

areas.
If you expect to develop a uniform seeding pattern, look

back often and avoid making turns with your seeder on

the ground. The more experienced you become the

better you will get at developing beautiful seed plots and

beautiful lawns.
Whenever you are done seeding always clean the seeder

out and perform all maintenance prescribed in the

Operator’s Manual. Never leave seed stored in the

hopper for prolonged periods. Never dismount your

tractor without first coming to a full stop, turning off the

tractor, and setting the park brake. Never allow riders on

the tractor when working with any rear mounted

implement installed.
With a little practice you should get very good at

developing lush green stands of grass with your Land

Pride NTS Seeder.

Содержание NTS2607















































































Результаты поиска

Содержание NTS2607

Отзывы:

Похожие инструкции для NTS2607

Бренды по названию

Популярные бренды

Land Pride NTS2607, Руководство оператора

Результаты поиска

Содержание NTS2607

Отзывы:

Похожие инструкции для NTS2607

Бренды по названию

Популярные бренды