background image

24

Section 2: Operating Instructions 

NTS2607, NTS2609, & NTS2611 No-Till Seeder 329-141M

Table of Contents

9/10/20

Hook-up Pull-Type Seeder

Refer to Figure 2-3:

WARNING

!

To avoid serious injury or death:  
Lightweight tractors with rear attached implements may need 

weights added to the front to maintain steering control. 

Consult your tractor Operator’s Manual to determine proper 

weight requirements and maximum weight limitations.

1. Make certain park jack (#14) is properly attached to 

jack mount (#20) and secured with detent pin (#13).

2. Adjust park jack as follows:

If seeder is resting on the ground, adjust park 

jack (#14) to support mainframe (#19) level. Do not 

adjust park jack to align clevis (#2) with tractor 

drawbar. Clevis height will be adjusted later in 

step 7.

If seeder was unhooked while raised off the 

ground, do not adjust park jack (#14) to align clevis 

(#2) with tractor drawbar. Clevis height will be 

adjusted later in step 7.

3. Store tractor’s upper center 3-point link in its storage 

hook.

4. Start tractor and raise 3-point lift arms fully up.

IMPORTANT: 

Detent pin (#13) must be fully inserted 

and secured before working on or around a seeder 

that is not hooked to the tractor drawbar.

IMPORTANT: 

 

(Drawbar to Clevis Height)

 

If clevis (#2) does not align properly with tractor 

drawbar during hook-up, the clevis height must be 

adjusted in hitch channel (#16). Do not adjust clevis 

height with park jack (#14). Using park jack to adjust 

clevis height can cause hydraulic lift cylinders to not 

function properly in the field.

5. Carefully back tractor within close proximity of 

clevis (#2).

6. Shut tractor down properly before dismounting. Refer 

to 

“Tractor Shutdown Procedure” 

on page 21.

7.

Hold clevis (#2) level. If tractor drawbar is higher or 

lower than clevis, adjust clevis in hitch channel (#16).
a. Remove nylock nut (#17) and bolt (#18).
b. Move clevis (#2) up or down until clevis (#2) is up 

one hole above tractor drawbar height.

c. Attach clevis (#2) to clevis hitch channel (#16) 

with existing 1"-8 x 6" GR5 bolt (#18) and nylock 

nut (#17). Draw nylock nut up snug. Do not 

tighten.

8. Rotate clevis (#2) level and insert wire retaining 

pin (#7) as follows:

If hydraulic lift cylinder (#8) is retracted as 
shown, insert wire retaining pin (#7) in one of 
the holes on the right side of clevis (#2).

If hydraulic lift cylinder (#8) is fully extended 
insert wire retaining pin (#7) in one of the holes 
on the left side of clevis (#2). 

9. Start tractor and continue to back tractor toward the 

seeder until hole in tractor drawbar and holes in 

seeder clevis hitch (#2) are aligned.

10. Shut tractor down properly before dismounting. 

11. Attach seeder to tractor drawbar by inserting 

customer supplied hitch pin (#6) through upper plate 

of clevis (#2), two upper washers (#1), tractor 

drawbar, as many lower washers (#1) as possible, 

and lower plate of clevis (#2). Secure hitch pin with 

customer supplied hitch pin keeper (#5).

NOTE:  

Hitch pin (#6) and keeper (#5) are customer 

supplied. The number of flat washers (#1) required 

will depend on tractor drawbar thickness. Not using 

flat washers can cause increased drawbar wear.

Tractor Hook-up to Pull-Type Seeder

Figure 2-3

37298

73360

Содержание NTS2607















































































Отзывы: