Land Pride 3P500 Скачать руководство пользователя

Страница: 34 / 52

Maintenance and Lubrication

Table of Contents

3P500, 3P500V, & 3P600



313-517M

2018-06-12

Seed Flap Replacement

Refer to Figure 21

To replace a seed flap

, use needle nose pliers or

similar tool to grasp “T” top of flap. Pull upward to remove
flap from metal bracket

Push new seed flap

down through metal bracket

until flap snaps into place with “T” top resting on top of
bracket.

If a Seed-Lok

or Keeton

seed firmer is also installed, it

may be necessary to shorten the flap.

Chain Maintenance

Initially check the drive chains after the first 10 hours of
drill use. The slack of new chains tends to increase
during the first few hours of operation due to seating.
Thereafter, check the chains every 100 hours.

Lubricate chains any time there is a chance of moisture,
and when being stored at the end of the planting season.

Chain Slack

Refer to Figure 22, which, for clarity, greatly exaggerates
slack, and omits the idlers.

Measure the span

for allowable slack:

Locate the longest span of each chain (usually the
span which does not run through the idlers).

Determine the ideal slack:
Long chains (over 36 inches / 91 cm):

in. per ft (21 mm/m)

Vertical short chains:

in. per ft (21 mm/m)

Horizontal short chains:

in. per foot (42 mm/m).

Measure the current slack

Acting at a right angle to the chain span at the center
of the span, deflect the chain in both directions. The
slack is the distance of the movement.

Adjust the idlers for ideal slack.

Whenever mounting a chain, make sure the clip at the
removable link is oriented to minimize snags.

Refer to Figure 23 (arrow shows chain direction)

Install clip with open end facing away from direction of
chain travel (shown by gray or striped arrows in chain
routing diagrams).

Figure 21

Seed Tube Flap

31047

Figure 22

Measuring Chain Slack

27264

Figure 23

Chain Clip Orientation

26482

Содержание 3P500





















































Результаты поиска

Содержание 3P500

Отзывы:

Похожие инструкции для 3P500

Бренды по названию

Популярные бренды

Land Pride 3P500, Оригинальное руководство пользователя

Результаты поиска

Содержание 3P500

Отзывы:

Похожие инструкции для 3P500

Бренды по названию

Популярные бренды