Land Pride 3P500 Скачать руководство пользователя | Manualshive

Страница: 3 / 52

background image

©

Copyright 2017 All rights Reserved

Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation
of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the
information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product
at the time of its publication, and may not reflect the product in the future.

Registered Trademarks of Great Plains Manufacturing, Inc. include:

Clear-Shot, Great Plains, Land Pride, Seed-Lok, Solid Stand.

Brand and Product Names that appear and are owned by others are trademarks of their respective owners. QR Code® is a registered trademark of Denso Wave, Inc.

Printed in the United States of America

ii

3P500, 3P500V & 3P600



313-517M

2018-06-12

Table of Contents

Important Safety Information...................................... 1
Safety Decals................................................................. 5
Introduction .................................................................. 9
Description of Unit.......................................................... 9

Intended Usage.......................................................... 9
Models Covered ......................................................... 9
Document Family ....................................................... 9

Using This Manual ....................................................... 10
Owner Assistance ........................................................ 10
Preparation and Setup............................................... 11
Pre-Setup Checklist ..................................................... 11
Hitching Tractor to Drill ................................................ 11
Electrical Connection (Option) ..................................... 12
Height and Leveling the Drill ........................................ 12
Operation Instructions .............................................. 13
Pre-Start Checklist ....................................................... 13
Transporting................................................................. 14

Use an Adequate Tractor (3-Point) .......................... 14
3P500 Example Weights.......................................... 14
3P500V Example Weights ....................................... 14
3P600 Example Weights.......................................... 14

Loading Seed............................................................... 15

Main Seed Box Loading ........................................... 15
Loading Small Seeds Box ........................................ 15

Acremeter Operation.................................................... 16

Normal Operating Sequence ................................... 16
Dormant Display ...................................................... 16

Field Operation ............................................................ 17
Parking......................................................................... 17
Storage ........................................................................ 17
Adjustments ............................................................... 18
Adjusting 3-Point Height .............................................. 19

00 Series Row Unit Adjustments ..................................20

Opener Springs ........................................................21
Disc Blade Adjustments............................................22
Disc Scraper Adjustment ..........................................23
Seed Firmer Adjustments .........................................24

®

Lock-Up (Option) ................................24

®

Seed Firmer Adjustment (Option) ..........24

Small Seeds Tube Adjustment (Option) ...................25
Opener Depth (Press Wheel Height) ........................25

Troubleshooting .........................................................26
Maintenance and Lubrication....................................28
Maintenance .................................................................28

Seed Clean-Out ........................................................29

Main Box Clean-Out .............................................29
Small Seeds Box Clean-Out .................................29

Seed Flap Replacement ...........................................30
Chain Maintenance...................................................30

Chain Slack...........................................................30

Gearbox Maintenance ..............................................31

Lubrication and Scheduled Maintenance .....................32
Options ........................................................................34

Seed Firmer ...........................................37

Appendix A - Reference Information ........................38
Specifications and Capacities: 3P500 and 3P600........38
Specifications and Capacities: 3P500V........................38
Tire Pressures ..............................................................39
Torque Values Chart ....................................................39
Drive System Diagrams................................................40
Appendix B - Pre-Delivery .........................................42
Appendix C - Accessory Installation ........................44
Carbide Disc Scraper Installation .................................44
Warranty ......................................................................47

«
1
2
3
4
5
...
»

Содержание 3P500





















































Отзывы:

Нет отзывов

Похожие инструкции для 3P500

Бренд: Daavlin Страницы: 13

Бренд: Daavlin Страницы: 27

ImageQuant LAS 4000

Бренд: GE Страницы: 86

Бренд: GE Страницы: 160

Бренд: GE Страницы: 134

Бренд: GE Страницы: 2

Druck DPI 620 Genii

Бренд: GE Страницы: 154

Arize Element Top Light

Бренд: GE Страницы: 2

Бренд: Datex-Ohmeda Страницы: 104

Druck DPI 620 Genii

Бренд: Baker Hughes Страницы: 166

Druck DPI 620 Genii

Бренд: Baker Hughes Страницы: 340

Бренд: SALUDA MEDICAL Страницы: 61

Бренд: Raven Страницы: 12

Бренд: Zero 88 Страницы: 20

Бренд: Kapriol Страницы: 32

Бренд: Cabletron Systems Страницы: 33

Бренд: i-CAT Страницы: 32

Бренд: Rain-Flo Irrigation Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды