manualshive.com logo in svg

Land Pride 3P500, Оригинальное руководство пользователя

Поделиться
Скачать
Land Pride 3P500 Скачать руководство пользователя страница 21

Operation Instructions

Table of Contents

2018-06-12

3P500, 3P500V, & 3P600

313-517M

17

Field Operation

1.

Hitch drill to a suitable tractor (page 11).

2.

Set seed population per rate chart and calibration, 
from Seed Rate manual.

3.

Load box with clean seed.

4.

Raise drill. Using calibration crank or 3-point gauge 
gauge wheel, operate the meter drive system. Check 
that feed cups, seed tubes and drives are working 
properly and free from foreign material by looking for 
seed flow under each opener.

5.

Lower drill. Set hitch to Float.

6.

Pull forward. Stop. Check tool bar height and opener 
depth.

7.

Begin seeding.

8.

Always lift drill out of the ground when turning at row 
ends and for other short-radius turns. Seeding stops 
automatically as drill is raised.

Parking

Perform the following steps when parking the drill for 36 
hours or less. Refer to “Storage”, to prepare for 
long-term storage.

1.

Park drill on a level, solid area.

2.

Lower 3-point hitch until drill is on the ground.

3.

Unplug wiring harness from tractor. Do not allow 
harness end to rest on the ground.

4.

Extend or retract the top link of the tractor until top 3- 
point pin is free. Remove pin.

5.

Remove pins from lower links.

Storage

Store drill where children do not play. If possible, store 
the drill inside for longer life.

1.

Unload seed boxes. Thoroughly clean 
seed-treatment residue from boxes and feed cups. 
See “Seed Clean-Out” on page 29.

2.

Remove any dirt and debris that can hold moisture 
and cause corrosion.

3.

Lubricate and adjust all roller chains.

4.

Take special care to oil feed cup drive sprocket in its 
square bore.

5.

Perform “Lubrication and Scheduled 
Maintenance” starting on page 32.

6.

Inspect drill for worn or damaged parts. Make repairs 
and service during the off season.

7.

Use spray paint to cover scratches, chips and worn 
areas on the drill to protect the metal.

8.

Disconnect seed hoses from openers. Permanent 
elongation and premature cracking of hoses may 
occur if stored connected. Plug hose ends to prevent 
pest entry into seed boxes.

9.

Cover with a tarp if stored outside.

Machine Damage Risk:
Never back up with openers in the ground. Seed tube and 
firmer damage is likely. Seed tube plugging is almost certain. 
Always raise the drill when stopped and prior to reversing.

Содержание 3P500





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды