Land Pride 326-461M Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 36

background image

26

Section 4: Maintenance & Lubrication

RCF2084 Rotary Cutters 326-461M

1/29/14

Table of Contents

Lubrication Points

Gauge Wheel Spindle Tube

Type of Lubrication: Grease

Quantity = 6 pumps

Gauge Wheel Hub

Type of Lubrication: Multi-purpose Grease

Quantity = 2 pumps

Gearbox

Method 1: Unscrew top vented dipstick (#1). Wipe oil from
dipstick and screw dipstick in without tightening. Unscrew
dipstick and check oil on dipstick. If below bottom level
mark, add recommended gear lube through dipstick hole
until oil reaches top mark on dipstick. Reinstall vented
dipstick and tighten.

Method 2: Remove side oil plug (#2). If oil is below bottom
of plug hole, add recommended gear lube through top
dipstick hole until oil flows out of side plug hole. Reinstall
and tighten side oil plug (#2) and vented dipstick (#1).

Type of Lubrication: 80-90W EP Gear Lube

Quantity = Fill until oil reaches top mark on dipstick or
begins to flow out side plug hole in gearbox.

NOTE: Do not overfill! Cutter should be level when
checking oil. Oil expands when hot, therefore, always
check oil level when cold.

30215

Do Not Overfill

IMPORTANT: Your cutter is shipped with a vented
dipstick packaged in the Operator’s Manual bag and
should have been installed in the gearbox by your
Land Pride dealer. Please see your Land Pride dealer
if vented dipstick was not included.

NOTE: Use a suction or siphon pump to drain
gearbox of oil when there is not an oil drain plug.

24

Hours

8

Hours

8

Hours

50

Hrs

Multi-purpose
spray lube

Multi-purpose
grease lube

Multi-purpose
oil lube

Intervals in hours at which
lubrication is required

Lubrication
Legend

33016

«
...
26
27
28
29
30
...
»

Содержание 326-461M





































Отзывы:

Нет отзывов

Похожие инструкции для 326-461M

Бренд: Gardena Страницы: 11

Бренд: Billy Goat Страницы: 13

Бренд: Echo Страницы: 8

Бренд: Echo Страницы: 44

Бренд: Echo Страницы: 52

Бренд: Echo Страницы: 62

Бренд: Tregaskiss Страницы: 24

Бренд: Cricut Страницы: 142

Greensmaster 3250-D

Бренд: Toro Страницы: 52

Team System Plus 440-1

Бренд: Logan Страницы: 2

Бренд: Dahle Страницы: 1

Бренд: Dahle Страницы: 5

Бренд: Maruyama Страницы: 32

Бренд: Maruyama Страницы: 56

Бренд: Maruyama Страницы: 60

Бренд: ADE Страницы: 12

Бренд: ADE Страницы: 20

Бренд: EINHELL Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды