Land Pride 326-461M Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 36

background image

11

Section 1: Assembly & Set-up

1/29/14

RCF2084 Rotary Cutters 326-461M

Table of Contents

Optional Rear Guards

!

DANGER

Do not operator cutter without a rear guard. Do not remove
rear guard unless it is replaced by an approved Land Pride
guard. Serious body injury or loss of life can result without an
attached rear guard.

Remove Rear Metal Band Deflector

Refer to Figure 1-5:

A metal band deflector is supplied standard with the
cutter and must be removed before the optional Rear
Single Chain Guard can be installed.

1.

Remove 1/2" whiz nuts (#3) and carriage bolts (#2).

2.

Remove Rear Metal Band Deflector (#1).

3.

Reattach whiz nuts (#3) and carriage bolts (#2) to
metal band deflector (#1) for safe keeping.

4.

Store Rear Metal Band Deflector with hardware for
future use when not using chain guard.

Rear Single Chain Guard

Refer to Figure 1-6:

1.

Remove Rear Metal Band Deflector following the
above instructions.

2.

Install rear chain guard (#2) with four 1/2"-13 x 1"
GR5 carriage bolts (#3) and hex whiz nuts (#5).
Draw whiz nuts up snug, do not tighten at this time.

3.

Install 1/2"-13 x 3 1/2" GR5 carriage bolts (#4),
deflector spacers (#5) and hex whiz nuts (#5). Draw
whiz nuts up snug.

4.

Tighten all whiz nuts (#5) to the correct torque.

Replaceable Skid Shoes (Accessory)

Refer to Figure 1-7:

326-120A

Skid Shoe Kit
(Includes 2 skid shoes & mounting hardware)

Replaceable skid shoes can be purchased from your
nearest Land Pride dealer. They bolt to the weld-on skid
shoes and help protect weld-on skid shoes and side
skirts from wear.

1.

Attach skid shoes (#1) to weld-on skid shoes with
3/8"-16 x 1" GR5 plow bolt (#2) and whiz nuts (#3).

2.

Tighten whiz nuts to the correct torque.

Rear Metal Band Deflector (Standard)

Figure 1-5

Rear Single Chain Guard Option

Figure 1-6

Skid Shoe Accessory

Figure 1-7

33137

33010

30993

«
...
11
12
13
14
15
...
»

Содержание 326-461M





































Отзывы:

Нет отзывов

Похожие инструкции для 326-461M

Бренд: Sandrigarden Страницы: 52

Бренд: Zenoah Страницы: 42

Бренд: QUINN Страницы: 8

Бренд: Textron Страницы: 10

Бренд: Craftsman Страницы: 26

Бренд: Craftsman Страницы: 26

Бренд: Craftsman Страницы: 23

Бренд: Craftsman Страницы: 18

Бренд: Craftsman Страницы: 37

Бренд: Craftsman Страницы: 47

Бренд: Craftsman Страницы: 52

Бренд: Fellowes Страницы: 20

Бренд: Fellowes Страницы: 28

ESSENTIAL OXYCUTTING

Бренд: Lincoln Electric Страницы: 42

Compact Classic 301-1

Бренд: Logan Страницы: 7

Бренд: HENX Страницы: 10

Бренд: US Cutter Страницы: 42

03200 Reelmaster 3100-D

Бренд: Toro Страницы: 385

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды