Land Pride 326-461M Скачать руководство пользователя | Manualshive

Страница: 6 / 36

background image

4

Important Safety Information

RCF2084 Rotary Cutters 326-461M

1/29/14

Table of Contents

Safety Labels

Your Rotary Cutter comes equipped with all safety labels in
place. They were designed to help you safely operate your
implement. Read and follow their directions.

1.

Keep all safety labels clean and legible.

2.

Refer to this section for proper label placement. Replace
all damaged or missing labels. Order new labels from your
nearest Land Pride dealer. To find your nearest dealer,
visit our dealer locator at www.landpride.com.

3.

Some new equipment installed during repair requires
safety labels to be affixed to the replaced component as

818-130C

Caution: 540 RPM

33020

33020

specified by Land Pride. When ordering new components
make sure the correct safety labels are included in the
request.

4.

Refer to this section for proper label placement.
To install new labels:
a.

Clean the area the label is to be placed.

b.

Spray soapy water on the surface where the label is to
be placed.

c.

Peel backing from label. Press firmly onto the surface.

d.

Squeeze out air bubbles with the edge of a credit card
or with a similar type straight edge.

818-830C

Safety Combo

«
...
4
5
6
7
8
...
»

Содержание 326-461M





































Отзывы:

Нет отзывов

Похожие инструкции для 326-461M

Бренд: D-CUT Страницы: 6

Бренд: U-Line Страницы: 13

Бренд: Zenoah Страницы: 64

Бренд: Esko Страницы: 59

Бренд: PrimAster Страницы: 44

Бренд: Meec tools Страницы: 20

Бренд: Meec tools Страницы: 69

Бренд: Amkus Страницы: 12

Бренд: Land Pride Страницы: 92

Micro Cross Cut PS600-75

Бренд: Peach Страницы: 18

Бренд: Breadman Страницы: 8

Бренд: REX Страницы: 3

Бренд: Valex Страницы: 28

POWERplus XQ POWXQ5320

Бренд: VARO Страницы: 11

Бренд: Parkside Страницы: 229

Бренд: GCC Technologies Страницы: 234

Бренд: Gude Страницы: 8

Бренд: Makita Страницы: 172

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды