Land Pride 326-461M Скачать руководство пользователя | Manualshive

Страница: 11 / 36

background image

9

Section 1: Assembly & Set-up

1/29/14

RCF2084 Rotary Cutters 326-461M

Table of Contents

4.

Insert stop pins (#1) through rear holes in hinge
plates (#2) and secure with cotter pins (#13). Bend
one or more legs of each cotter pin to keep cotter
pins from falling out.

5.

Attach hinge plates (#2) to rear braces (#12) as
follows:

a. Rotate hinge plates (#2) up until stop pin (#1) is

above hitch brace bars (#6) as shown in Detail-A.

b. Insert 3/4"-10 x 4 1/2" GR5 cap screw (#9A)

through rear brace bar (#6), flat washer (#15),
hinge plates (#2), 1 5/8" long bushing (#3), hinge
plates (#2), flat washer (#15), and rear brace
bar (#6). Secure cap screw (#9A) with hex flange
lock nut (#11).

c. Draw locknut (#11) up snug and then back-off

1/4 turn.

6.

Insert clevis pin (#19) through hitch straps (#4 & #5)
and secure with hair pin cotter (#13).

7.

Insert hitch pins (#20) into clevis plates as shown
and secure with linchpins (#18).

Hitch Assembly

Figure 1-2

33132

End with 11/32" Dia. hole

End with 13/32" Dia.

1 3/4" O.D.
Washers

3-Point Hitch Assembly

Refer to Figure 1-2 on page 9:

1.

Attach the smaller 11/32" diameter hole in rear
braces (#6) to rear deck lugs as shown using
5/8"-11 x 1 3/4" GR5 cap screws (#8A) and hex
flange locknuts (#12). Draw locknuts (#12) up snug
and then back-off 1/4 turn.

2.

Attach left and right-hand hitch straps (#4 & #5) to
cutter deck with 5/8"-11 x 1 3/4" GR5 bolts (#8B),
bushings (#10), 1 3/4" OD flat washers (#14), and
hex flange lock nuts (#12). Tighten lock nuts to the
correct torque.

3.

Attach hinge plates (#2) to hitch straps (#4 & #5) as
follows:

a. With notch in driveline chain clip (#7) facing up

and towards the front as shown in Detail-A, insert
3/4"-10 x 4 1/2" GR5 cap screw (#9B) through
chain clip (#7), left hitch strap (#4), machine
washer (#16), hinge plates (#2), 1 5/8" long
bushing (#3), hinge plates (#2), machine
washer (#16), right hitch strap (#5), and hex
flange lock nut (#11).

b. Draw locknut (#11) up snug and then back-off

1/4 turn.

NOTE: Bolts (#8A, #9A, & #9B,) must be loose so
that hinge plates (#2) can pivot freely.

«
...
9
10
11
12
13
...
»

Содержание 326-461M





































Отзывы:

Нет отзывов

Похожие инструкции для 326-461M

Бренд: LaneShark Страницы: 43

Бренд: Waytex Страницы: 32

NZ 3200 - AXIS ERGO

Бренд: Robland Страницы: 21

Бренд: Battipav Страницы: 15

Бренд: Marshalltown Страницы: 32

Бренд: Raider Страницы: 76

Бренд: Spellbinders Страницы: 24

Бренд: SIRI Страницы: 11

Бренд: US Cutter Страницы: 50

Бренд: Parkside Страницы: 52

Бренд: Hypertherm Страницы: 223

Бренд: Land Pride Страницы: 66

Бренд: Land Pride Страницы: 84

Бренд: Tanaka Страницы: 21

Бренд: Efco Страницы: 80

Бренд: Gude Страницы: 8

Бренд: Husqvarna Страницы: 72

Бренд: DeWalt Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды