Lamtec AEC-TPS Скачать руководство пользователя страница 107 | Manualshive

Страница: 107 / 284

background image

106

5

Functional Description with Process Diagrams

5.4.3.6 Burner Shut-OFF

P no.

Description

Attributes

44

Start-up sequence: firing-rate [Digit]

V1.0.0.0

Start-up output in digit depending on internal firing-rate.
Enter the burner firing-rate with which the burner shall start in the start-up sequence.

Write: 0/GUI/UI
Read: 0
Default: 0
Min: 0
Max:999

45

Start-up sequence: start-up time [s]

V1.0.0.0

Start-up time in s
Enter the maximum duration, during which the start-up sequence should effect.

Write: 0/GUI/UI
Read: 0
Default: 1
Min: 0
Max:32767

46

External firing-rate limit [Digit]

V1.0.0.0

External firing-rate limit in digit depending on the internal firing-rate.
Only for activated burner firing-rate controller.

Write: 0/GUI/UI
Read: 0
Default: 999
Min: 0
Max:999

P no.

Description

Attributes

47

Soft stop time



burner run-out time [s]

V1.0.0.0

Currently without function.

Write: 0/GUI/UI
Read: 0
Default: 0
Min: 0
Max:100

54

switch-on threshold

V1.0.0.0

Switch-off hysteresis for the lower control range
If the actual value falls below the setpoint minus the value set in this parameter, the burner is
switched on again.
Enter the switch-on point as the difference to the setpoint.
Switch on value = setpoint value - parameter content.
Example: The burner shall start at 110.
Setpoint value = 120, parameter value = 10, switch-on point = 120 - 10 = 110.
If the burner should switch on again above the setpoint, negative values can also be
entered. Thereby corresponds -1 = 65535 and -999 = 64537.
Parameter content = 65536 - difference.
Example: The burner shall start at 125.
Setpoint value = 120, parameter value = 65536 - 5 = 65531, switch-on point = 120 - (-5) =
125.

Write: 0/GUI/UI
Read: 0
Default: 1
Min: -32768
Max: 32767

55

Switch-off threshold for the upper control range

V1.0.0.0

Switch-off hysteresis of the upper control range in °C or bar (x.xx)
Input of the upper control range. If the actual value exceeds the setpoint by this value, the
burner runs at base fire.
The value entered corresponds to the difference between the current setpoint and the upper
limit of the control range. Depending on the setting in P 61, the content is interpreted as °C
(directly without decimal point) as bar (resolution 0.1 bar - range 0.1 to 99.9 bar) or in digits.

Write: 0/GUI/UI
Read: 0
Default: 5
Min: 0
Max:999

«
...
105
106
107
108
109
...
»

Содержание AEC-TPS





























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AEC-TPS

AF-600 FP Series

Бренд: GE Страницы: 7

Бренд: Jafar Страницы: 9

Бренд: GARDTEC Страницы: 48

Бренд: FAAC Страницы: 64

Бренд: Harsco Industrial Страницы: 57

Бренд: Harmar Mobility Страницы: 53

CentriPro Aquavar SOLO

Бренд: Xylem Страницы: 48

phyCORE-MCF548x

Бренд: Phytec Страницы: 104

Бренд: Baier Страницы: 20

Бренд: Blucave Страницы: 2

Бренд: Daikin Страницы: 40

Бренд: Carel Страницы: 36

Бренд: Handiquilter Страницы: 53

Бренд: Nibe Страницы: 92

Бренд: Yoshitake Страницы: 21

Бренд: Oasis Страницы: 7

GA INDUSTRIES Figures 251-D

Бренд: Vag Страницы: 6

Бренд: FOR-A Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды