Lambrecht rain[e]observer Скачать руководство пользователя страница 8

Страница: 8 / 44

rain[e]observer

Operating Instructions

Operating Instructions

rain[e]observer Precipitation Measuring System

9.2 Wiring the rain[e] as rain[e]observer · Internal connection diagram

If the observer module is retrofitted to a rain[e] precipitation sensor or if it is not supplied with a rain[e] prepared

for the rain[e]observer, the configuration of the 8-pin device plug in the precipitation sensor must be wired in ac

cordance with the following connection diagram.

It is important that the configuration of wires with the thick lines (WH, BN, GY, PK) is strictly

adhered to. All other wires can be connected as desired.

Note:

It is not possible to use the SDI-12 interface and the RS485 interface at the same time. To avoid malfunc

tions, it is recommended that only one of the two interfaces be connected to the plug connector internally. Com-

munication via the SDI-12 interface is provided as standard; for the RS485 interface connection, see the section

Changing the serial interface from SDI-12 (default) to RS485

To change the wiring, open the housing.

Содержание rain[e]observer













































Результаты поиска

Содержание rain[e]observer

Отзывы:

Бренды по названию

Популярные бренды

Lambrecht rain[e]observer, Руководство по эксплуатации

Результаты поиска

Содержание rain[e]observer

Отзывы:

Бренды по названию

Популярные бренды