162
Programming
Figure 9-4 IFM control module and LED
6.
Press the button of the multi-cycle configuration switch the number of times you want the packer
to make continous cycles.
7.
Once you have entered the desired number of cycles, the LED flashes blue the same number of
times to confirm that the new settings have been stored.
8.
To test the new packer settings, press the green
START CYCLE
button on the control station.
9.
Once the test completed, switch off the hydraulic pump and stop the engine.
10.
Close the control station and reinstall the screws that secure it to the control panel.
11.
If the truck is not to be used right away, lock out and tag out the vehicle (see
Allison Transmission Programming
In Allison transmissions used on automated vehicles, the transmission control module (TCM)
manages several functions:
It prevents the pump from over speeding (2,000
rpm,
maximum).
It prevents the pump from engaging if the engine speed is higher than 900
rpm.
It shuts off the arm joystick if the vehicle is moving faster than 15
mph
(25
km/h).
It also controls the auto-neutral system (if present).
If the TCM installed on your vehicle requires repair or replacement, or if it needs specific
programming parameters, see
Programmed Parameters
below.
Programmed Parameters
Programming the TCM affects engine speed,
PTO
engagement and operation, as well as the optional
auto-neutral system. If the TCM is replaced, it must be reprogrammed to reset the vehicle operating
parameters. Refer to Table 1 to reprogram the TCM.
Содержание Automizer Versa Hand
