background image

Page 14

3.D  Vertical Venting - Category I 

 

All venting must comply with fuel gas code and be 

installed by a licensed installer. 

This boiler can be vented into a masonry chimney, 

(see Figure 7 and Figure 8 on page 12) provided 

several conditions are met:
1.  The chimney must have an appropriate lining that 

is clean, properly constructed and properly sized.

2.  The chimney passage way shall be examined to 

ascertain that it is clear and free of obstructions. 

3.  If a chimney rebuild is required, it shall conform 

to nationally recognized standards (see National 

Building Code or ANSI/NFPA 211).

4.  The boiler must not be connected to a fireplace, 

wood stove or other solid fuel burning equipment.

5.  When the boiler and a hot water heater are to be 

connected to the same chimney, they must have 

their own vent connector and enter the chimney at 

least 6” (152mm) apart.

IMPORTANT NOTE: Always provide a minimum 

clearance of 6” (152mm) between Type C (single 

wall) vent pipe and any combustible materials. 

NOTE: Exterior masonry chimneys in very cold 

environments are at risk of condensing due to the 

high efficiency of this equipment.  Insulated liners 

are recommended based on local conditions and 

expected system water temperatures.  Also ensure 

the boiler’s anti-condensing features are utilized by 

properly wiring the system pumps. See Figure 28 on 

page 27 

 

WARNING

Do not store any chemical, cleaners, or other 

corrosive material near combustion air openings 

or in the room. Avoid locating dryer vents in the 

vicinity of combustion air openings. Failure to 

prevent corrosive materials from mixing with 

combustion air can result in reduced boiler life 

and unsafe boiler operation.

 

AVERTISSEMENT

N’entrepposer aucun produit chimique, produit 

nettoyant ou produit corrosif à proximité des 

bouches d’air de combustion ou dans la pièce. 

Éviter de placer des tuyaux de ventilation pour 

sécheuse à proximité des bouches d’air de 

combustion. Le fait de laisser des maitières 

corrosives se mélanger à l’air de combustion 

risque de réduire le cycle de vie de l’appareil 

de chauffage et de compromettre son 

fonctionnement.

 

 

WARNING

Single wall vent pipe must NEVER pass through 

interior walls or through floors or ceilings! Failure 

to comply with this warning could result in a fire 

causing property damage, personal injury, or death!

 

 
 

 

AVERTISSEMENT

Paroi simple tuyau d'évent doit jamais passer par 

l'intérieur les murs ou par planchers ou plafonds 

! Le non-respect de cet avertissement peut 

provoquer un incendie causant des dommages 

matériels ou corporels, ou de mort!

 

LAARS Heating Systems

Содержание MINI-THERM JX





















































Отзывы: