Laarmann LMFC250 Скачать руководство пользователя страница 36

Страница: 36 / 47

LMFC250 FINE CRUSHER MANUAL

6.1

Operator

’

s Controls

Minimum PPE required for jobs contained in the workshop section of this manual.

8.1

General Safety Rules

8.2

Test and Inspection Procedures

8.2.1

Special Test Equipment

Procedures for testing and inspection of the LMFC 250 Crusher are as per the user

’

s company requirements.

8.2.2

Crusher will not start

Not applicable. No special test equipment is required for use on the LMFC 250 Crusher.

The following procedure outlines the steps for testing and inspecting the Crusher.

•

Perform a visual inspection on parts that are likely to wear, such as the jaw plates and side liners, V belts and any breakdown of
bearings.

•

Check that there is no excessive dust build up around the Crusher.

•

Check that all electrical cables, plugs and sockets are free from damage and connected correctly.

•

Check the tension of the V belts.

•

Ensure the hopper lid opens and closes freely and without obstruction.

•

Ensure the lubrication points have been adequately lubricated.

8.2.3

Testing Standards

Not applicable

8.2.4

Adjustments for Test or Inspection

No adjustments for test or inspection are required on the LMFC 250 Crusher.

8.3

Troubleshooting Procedures

Refer to the Maintenance Section of this Manual for a detailed Troubleshooting Guide and procedures.

Содержание LMFC250
















































Результаты поиска

Содержание LMFC250

Отзывы:

Похожие инструкции для LMFC250

Бренды по названию

Популярные бренды

Laarmann LMFC250, Руководство пользователя

Результаты поиска

Содержание LMFC250

Отзывы:

Похожие инструкции для LMFC250

Бренды по названию

Популярные бренды