Laarmann LMFC250 Скачать руководство пользователя страница 30

Страница: 30 / 47

LMFC250 FINE CRUSHER MANUAL

Step 6:

Using two (2) M8 eyebolts, carefully lift the jaw plate out from the Crusher frame leaving the T clamp at the bottom of

the draw bolts.

Note

: The eyebolts screwed into the top end of the jaw plates make it easier to remove the plates from the machine.

Undone Draw Bolt

Jaw Plate Locating Ledge

T Clamp

Fig 7. Jaw plate T clamp and draw bolts.

Warning:

Personnel Danger/Hazard –

Exercise caution when removing the jaw plates to prevent injury. Each

plate weighs approx.

’ 25

kg.

Step 7:

Repeat Step 6 for the other jaw plate, then thoroughly clean the whole area where the jaw plates and side liners loca-

te, prior to installing new plates.

Step 8:

The jaw plates can be rotated only once before being replaced by new ones. Relocate the rotated or new jaw plates

into position on the T clamps and draw them up with the draw bolts.

Front Body Plate

Step 9:

The new side liners can only be installed in one direction, as they have a full chamfer on the rear edge towards the

moving jaw plate and a half chamfer on the front edge. When located in place, give them a slight tap on top to help them seat
properly.

Step 10:

adjust the jaw plate gap as per Section 6.5.3, Steps 4 to 8 in this section of the manual.

Step 11:

Replace all covers and reconnect power to test run the machine.

Note

Machinery Damage/Hazard –

After changing the jaw plates and/or side liners, check the jaw plates draw

bolt tension at 12 hours & 120 hours of operation & every 20 hours thereafter.

Содержание LMFC250
















































Результаты поиска

Содержание LMFC250

Отзывы:

Похожие инструкции для LMFC250

Бренды по названию

Популярные бренды

Laarmann LMFC250, Руководство пользователя

Результаты поиска

Содержание LMFC250

Отзывы:

Похожие инструкции для LMFC250

Бренды по названию

Популярные бренды