Laarmann LMFC250 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 47

background image

The following section outlines all the relevant storage, transport and handling requirements for the LMFC 250 Crusher.

14

LMFC250 FINE CRUSHER MANUAL

3

Transportation & Handling

Minimum PPE used in this section

3.1

General safety rules

Only trained operators of forklifts or cranes are to lift or move the crated or un

-

crated LMFC 250 Crusher.

3.2

Storage, Transportation and Handling

The sections below outline steps and procedures for the transportation, handling and unpacking of the LMFC 250 Crusher
and storage of the machine if required.

3.2.1

Storage

If the machine needs to be stored for any reason, it should be indoors or undercover away from the effects of the weather.

3.2.2

Transportation

The packing crate has a pallet base for ease of access and movement with a forklift. The forklift must have a rated capacity
to lift the crated machine.

Please note, under no circumstances are slings or chains to be used to lift the crated machine. Always lift the machine
utilizing the recesses in the pallet base with a forklift.

3.2.3

Handling

Always use the forklift to lift and move the Crusher. Placing the Crusher close to the installation point, prior to unpacking, will
prevent unnecessary moving and therefore reduce the risk of injury.

«
...
12
13
14
15
16
...
»

Содержание LMFC250
















































Отзывы:

Нет отзывов

Похожие инструкции для LMFC250

Бренд: Baker Instrument Company Страницы: 24

Бренд: YSI Страницы: 70

Бренд: Eaton Страницы: 16

Бренд: Eaton Страницы: 15

Бренд: Hakko Electronics Страницы: 8

Бренд: Hainbuch Страницы: 52

Бренд: VBM Страницы: 36

Бренд: W&H Med Страницы: 122

Ransomes HR 6010

Бренд: Jacobsen Страницы: 10

Бренд: Jacto Страницы: 64

FlexDraper FD2 Series

Бренд: MacDon Страницы: 2

OXYGEN PRO MINI

Бренд: M-Audio Страницы: 56

Бренд: Nektar Страницы: 12

Бренд: Olsen Страницы: 58

Бренд: TANACOM Страницы: 27

Бренд: iBACheck Страницы: 2

Бренд: ValueStore US Страницы: 2

MCX-C15 - MusicCAST Network Audio Player

Бренд: Yamaha Страницы: 65

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды