L-Card L-502-P-G-D-I Скачать руководство пользователя

Страница: 3 / 73

Revision history of this document

Date

Document
revision

Contents of the change

06.2012

1.0.1

Preliminary data

07.2012

1.0.2

Preliminary data

11.2012

1.0.3

The information on connection L-502 is added, as well as

an item

, item

, item

, item

item ... is added by

01.2014

1.0.4

Edited

table 4-1

, supplemented paragraphs.

05.2014

1.0.5

A comment is added to the item

5.1.2

, page

06.2014

1.0.6

Different names of signals are fixed: SYNC_IN, SYNC_OUT is
changed to START_IN, START_OUT, accordingly.

05.2015

1.0.7

Added item

3.3.5

, item .

5.5.1

03.2016

1.0.8

Added

Chapter 7

02.2017

1.0.9

Paragraph added

3.3.4.1

07.2017

1.0.10

A warning is added to item.

3.3.5.2

10.2017

1.1.0

Added industrial design versions.
The characteristics according to the results
of preparation of the family of

L-CARD voltage measuring

converters

for certification as Means of Measurement are brought

into correspondence. Added to item

3.3.8

. Paragraph added

4.5

When reading this document electronically, to facilitate navigation, use the electronic

tree of the table of contents (for example, Acrobat Reader), as well as hyperlinks within the
document.

Содержание L-502-P-G-D-I










































































Результаты поиска

Содержание L-502-P-G-D-I

Отзывы:

Похожие инструкции для L-502-P-G-D-I

Бренды по названию

Популярные бренды

L-Card L-502-P-G-D-I, Руководство пользователя

Результаты поиска

Содержание L-502-P-G-D-I

Отзывы:

Похожие инструкции для L-502-P-G-D-I

Бренды по названию

Популярные бренды