L-Card L-502-P-G-D-I Скачать руководство пользователя страница 59

Страница: 59 / 73

Chapter 6. Connexion samples.

These connection examples should be considered together with the recommendations for

connecting and configuring the L-502 (n.

4.5

The short form of information provided in this chapter does not cover all the features of the

connection for your particular case. If necessary, please contact:

[email protected]

or in the conference on the

site

en.lcard.ru

6.1. ADC entry point connection

6.1.1. Connecting to the ADC entry point of single-phase voltage source

6.1.1.1. Up to 32 channels. Mode "with
common ground"

6.1.1.2. Up to 16 channels. "Differential"
mode

L-502

X1 (X2-X16, Y1-Y16)

AGND

GND32

вх

L-502

AGND

X1 (X2 -X16)

Y1 (Y2 -Y16)

вх

Forbidden to connect in this way!:

L-502

AGND

X1 (X2-X16, Y1-Y16)

L-502

GND32

X1 (X2-X16, Y1-Y16)

L-502

X1 (X2 -X16)

Y1 (Y2 -Y16)

Содержание L-502-P-G-D-I










































































Результаты поиска

Содержание L-502-P-G-D-I

Отзывы:

Бренды по названию

Популярные бренды

L-Card L-502-P-G-D-I, Руководство пользователя

Результаты поиска

Содержание L-502-P-G-D-I

Отзывы:

Бренды по названию

Популярные бренды