L-Card L-502-P-G-D-I Скачать руководство пользователя страница 38

Страница: 38 / 73

Connection of signals.

4.2.3.1. What gives an independent resolution to the outputs of the high and low
byte?

One of the important practical examples is a system of 3 buses with a width of 8 bits each, as

shown in the figure below. The first bus is the input one, the second is the output bus, the third is bi-
directional.

DI1...DI8

DO1...DO8

DI9...DI16

DO9...DO16

бит

DI_SYN1

DI_SYN2

L-502

бит

Fig. 4-3: Example of a grouped connection of digital lines: three buses of 8 bits each.

With the addition of two additional universal inputs DI_SYN1, DI_SYN2, we get an almost

important case of implementing interfaces with different devices that have an 8-bit bidirectional
data bus, input and output control lines.

4.2.4. Internal connector of intermodule synchronization.

The pinout for the synchronization connector for all versions of L-502 is identical, but in

version 3, an angled connector is used.

CONV_OUT

START_OUT

DGND

CONV_IN

DGND

START_IN

Fig. 4-4: Intermodule synchronization

connector (L-502 version 1 and 2).

8 bits

Содержание L-502-P-G-D-I










































































Результаты поиска

Содержание L-502-P-G-D-I

Отзывы:

Бренды по названию

Популярные бренды

L-Card L-502-P-G-D-I, Руководство пользователя

Результаты поиска

Содержание L-502-P-G-D-I

Отзывы:

Бренды по названию

Популярные бренды