L-Acoustics LA4X Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 83

background image

Operation

OUT CH TEMP (%)

OUT CH TEMP (%) (output channel temperature) displays the temperature measured at each individual amplier circuit

output as a percentage of the maximum operating temperature supported by the amplied controller: 60° C / 140° F =

100%.

‽OUT CH TEMP (%) ‼
52% 53% 50% 48%

For example in this illustration, the temperature of channels OUT 1 to OUT 4 is respectively 52, 53, 50, and 48% of the

maximum values.
Refer to

Error messages

(p.64) for information on the temperature-related messages.

ETHERNET LINKS

ETHERNET LINKS displays the current status of the link of each Ethernet port.
This function is only available on LA4X with 1 Gbit/s Ethernet ports. Refer to the

Networking and control of LA4X

with 1 Gbit/s Ethernet ports

technical bulletin for more information.

The status includes, for each port:

• the Ethernet link speed: 10M (for 10 Mbits/s), 100 (for 100 Mbits/s) or 1G (for 1 Gbits/s)
• the communication mode: HALF (for half-duplex) or FULL (for full-duplex)

If no connection has been established, the displayed status is DOWN.
Possible causes: no cable connected to the port, faulty cable connected to the port, cable connected to the port but no

device connected at the other end of the cable, port failure.

‽ETHERNET LINKS ‼
1: 1G FULL 2:100 FULL

For example, in this illustration, port 1 has a speed of 1 Gbits/s, port 2 has a speed of 100 Mbits/s, and both are in full-

duplex mode.

AVB CLOCK STATUS

AVB CLOCK STATUS displays the current status of the AVB clock.

• LA4X amplied controllers with HARDWARE INFO

ID1

,

ID2

or

ID3

(in MONITORING & INFO menu) do not

support AVB. These Units can be upgraded to support AVB by purchasing and installing KR LA4XDSP2.

• LA4X amplied controllers with HARDWARE INFO

ID4

or higher (in MONITORING & INFO menu) support AVB.

The status can be:

• DISABLED: No clock (the amplied controller is not connected to any AVB network).
• SLAVE: The amplied controller sets its clock on the clock of the gPTP grandmaster in the AVB network it is connected

to.

• ROOT: The amplied controller is the gPTP grandmaster in the AVB network it is connected to.

‽AVB CLOCK STATUS ‼
DISABLED

For example, in the illustration, status is DISABLED.

FIRMWARE

FIRMWARE displays the version number of the amplied controller onboard rmware.
Press the encoder wheel to display the fourth digit and the build date (in the YYYYMMDD format).

‽FIRMWARE ‼
V2.8.1

‽FIRMWARE 20170512
V2.8.1.4

Network

Always ensure that all LA4X amplied controllers used in a given network run the same rmware version.

50

LA4X owner's manual (EN) version 14.1

«
...
48
49
50
51
52
...
»

Содержание LA4X




















































































Отзывы:

Нет отзывов

Похожие инструкции для LA4X

Бренд: 5Core Страницы: 2

Бренд: Make Noise Страницы: 10

Бренд: TC Electronic Страницы: 45

Бренд: EAW Страницы: 24

Бренд: Sponsler Страницы: 4

Бренд: Intelix Страницы: 12

Бренд: QUAD Страницы: 16

TUBE SCREAMER AMPLIFIER

Бренд: Ibanez Страницы: 52

Бренд: Stageline Страницы: 18

JBL Commercial VMA Series

Бренд: Harman Страницы: 28

Бренд: Marshall Amplification Страницы: 1

Бренд: Rockville Страницы: 12

Бренд: Harris Страницы: 56

Бренд: McIntosh Страницы: 28

Бренд: Macab Страницы: 2

Бренд: Mutant Страницы: 24

Бренд: Ssl Страницы: 8

Бренд: Fenton Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды