Kysor/Warren QILG 06 Скачать руководство пользователя | Manualshive

Страница: 5 / 36

background image

5

Introductions - General Information

This manual has been prepared for our customers and the personnel involved in setting up and
maintaining our cases.

ICON KEY

Caution

Special Note

Warning

CAUTION

: Failure to maintain maximum design conditions may result in operational issues such

as: increased BTU load, high product temperature, coil icing, product frosting, and internal and external
sweating. Failure to follow factory recommendations for installation and set-up may cause operational
issues and will void standard warranty.

Case Description

Model

Description

QILG – 06, 08, 12

Frozen Food / Ice Cream Island Case with glass front, 6 ft., 8 ft or 12
ft. lengths; offered with electric, off-cycle or hot gas defrost

Receiving/Shipping Damage/Lost Items

All equipment should be examined for shipping damage before and during unloading. If there is any
damage, the carrier should be notified immediately and an inspection requested. The delivery receipt must
be noted that the equipment was received damaged. If damage is of a concealed nature, you must contact
the carrier within three (3) days following delivery. The consignee must file a claim with the carrier.

NOTE

: All claims for shortages must be within 10 days after receipt of shipment.

The Kysor/Warren case is designed to provide years of trouble free service.

Kysor/Warren Frozen Food / Ice Cream Cases

are designed to

merchandise  frozen  food  products.    These  cases  should  be  installed  and
operated  according  to  the  instructions  contained  in  this  manual  to  insure
proper  performance.    They  are  designed  for  display  of  products  in  an  air-
conditioned  store  where  temperature  and  humidity  are  maintained  at  a

maximum of 75% dry-bulb temperatures and 55% relative humidity

.

«
...
3
4
5
6
7
...
»

Содержание QILG 06





































Отзывы:

Нет отзывов

Похожие инструкции для QILG 06

Бренд: L3 Aviation Products Страницы: 27

Бренд: Nemco Страницы: 2

Бренд: Zanussi Страницы: 4

DENSEI MACHIDA FB-R5F11PLG

Бренд: Naito Страницы: 5

Бренд: Avidyne Страницы: 198

Бренд: Garmin Страницы: 76

Бренд: Toolots Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды