manualshive.com logo in svg

Kysor/Warren QILG 06, Руководство по установке и эксплуатации

Поделиться
Скачать
Kysor/Warren QILG 06 Скачать руководство пользователя страница 29

29 

 

  

WARNING!

 DO NOT USE HOT water on COLD glass surfaces. This could cause the glass to 

shatter  and  could  result  in  personal  injury.  Glass  fronts  and  ends  should  be  warm  before  applying  hot 
water 

CAUTION

: The following could damage the case: 

 

Do  not  use  solvent,  oil  or  acidic-based  cleaners  on  any  interior  surfaces  as  the  surface  may 
become damaged. 

 

Do not use abrasive cleaners and scouring pads, as these will mar the finish. 

 

Never introduce water into the case faster than the waste outlet can release it. 

 

DO

 

NOT

 

USE

 

STEAM

 

OR

 

HIGH

 

PRESSURE

 

SYSTEMS

 

TO

 

CLEAN

 

THE

 

CASE

 

AS

 

SEALS

 

MAY

 

BE

 

BROKEN

 

WHICH

 

WILL

 

CAUSE

 

THE

 

CASE

 

TO

 

LEAK. 

Shelves 

Do not use a hose or submerge shelves in water. Wipe the shelves clean with a wet sponge or cloth so that 
water will not enter the light rails.  

Mirrors 

Mirrors  are  sheets  of  clear  glass  that  have  a  very  thin  reflective  coating  applied  to  one  side.  These 
coatings are susceptible to deterioration if certain cleaning solutions and even water are allowed to come 
in contact with them. Every precaution should be made to keep liquids away from the coated side of the 
mirrors.  If  liquids  are  allowed  to  flow  along  the  face  side  of  the  mirror to  its  edge,  the  liquid  can  seep 
between the coating and the glass, causing serious damage. 
To help prolong the life of the mirrors: 

•

 

Use only mild cleaning solutions (Windex, Solox, or a weak solution of vinegar and water.) 

•

 

Do NOT spray liquids on mirrors. Dampen the cleaning cloth, and then use the cloth to wipe the 

mirror. 

•

 

Wipe water from the mirrors immediately to prevent difficult to remove water spots and also to 

prevent the water from reaching the mirrors edge. 

•

 

Never use dirty cloths, scrapers or any other abrasive materials for cleaning. 

Honeycomb Assembly 

Honeycomb should be cleaned every 6-8 months, depending on store conditions. The Honeycomb may be 
cleaned with a vacuum cleaner or be removed and washed with soap and water. The honeycomb must be 
completely dry before returning it to the case. 

 
 
 

NOTE

:  The  position  and  angle  of  the  honeycomb  when  removing  from  the  case. 

Honeycomb must be replaced at the same angle.

 

Содержание QILG 06





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды