Kyoritsu Electrical Instruments Works KEW 2062 Скачать руководство пользователя страница 38

Страница: 38 / 49

Chapter 7 Other functions

KEW 2062/2062BT

- 37 -

KEW 2062/2062BT

Chapter 7 Other functions

[Data hold function]

The LCD shows “ ” in the upper left corner by pressing data hold button and hold the currently

displayed reading. In this state, the instrument is performing measurements; however, the

reading isn’t updated. Press the Data hold button again to exit from the data hold mode, then

treading update resumes and the “ ” disappears.

By switching the measurement function, data hold is disabled, and measurement starts on the

selected function.

[Auto-backlight-off]

Backlight turns off automatically when 5 min. pass after the last key operation. To turn it on

again, hold down (long press) the Item switching button [

◄

]. Then the lighting time will be

extended 5 min. A long press of Item switching button

[◄], while the

light is on, turns off the light.

When setting the backlight to OFF, written in page 19, the auto-off function is disabled. In this

state, backlight doesn’t turn off when 5 min pass. To turn off the light, in this case, hold down

the Item switching button [

◄

[Auto-power-off]

Note

● If the instrument is off with the function switch set to a measurement position

, auto-power-off

function might activate and turn off the instrument.

Except for Bluetooth communication, the instrument turns off automatically when 15 min. pass

after the last key operation; discontinuous buzzer sounds 4 times. To turn on the instrument again,

set the function switch to OFF and then set it to the desired measurement position.

[Auto-ranging – current]

Current range switches automatically according to the measured rms currents.

A range shifts to one upper range when the input exceeds 110% or 300% peak (absolute

value) of the currently selected range and shifts to one lower range when the input drops 90% rms.

While “MAX”, “MIN”, “AVG”, and “|PEAK| (peak value)” has been selected in the display mode,

auto-ranging doesn’t work: the selected range is fixed and used.

KEW 2062/2062BT

Chapter 8 Bluetooth communication

KEW 2062/2062BT

- 38 -

Chapter 8 Bluetooth communication

WARNING

●

Radio waves at Bluetooth communication may affect the operations of medical electronic

devices. Special care should be taken when using Bluetooth connection in the areas where

such devices are present.

Note

●

Using the instrument or tablet devices near wireless LAN devices (IEEE802.11.b/ g) may

cause radio interferences, lowering of communication speed, resulting in significant time lag

in the display update rate between the instrument and tablet device. In this case, keep the

instrument and the tablet device away from the wireless LAN devices, or turn off the wireless

LAN devices or shorten the distance between the instrument and the tablet device.

● It may be difficult to establish

communication connection if either the instrument or tablet

device is in a metal box. In such a case, change the measurement location or remove the

metal obstacle between the instrument and the tablet device.

● If any leaking of data or information occurs while making a communication using Bluetooth

function, we assume no responsibility for any released content.

● Some tablet devices, even if the application runs properly, may fail to establish

communi-

cation with the instrument. Please use another tablet device and try to communicate with.

If you still cannot confirm the connection, there may be some problem with the instrument

unit. Please contact your local KYORITSU distributor.

● The Bluetooth word mark and logos are owned by Bluetooth SIG, Inc. and we, KYORITSU,

are licensed by them for use.

● Android, Google P

lay Store, and Google Map are the trademark or registered trademark of

Google Inc.

● iOS is the trademark or registered trademark of Cisco.

● Apple Store is the service mark of Apple Inc.

● In this manual, the “TM” and “ ® ” marks are omitted

KEW 2062BT has a Bluetooth communication function and can exchange data with Android/

iOS tablet devices. Using the special application “KEW Power*(asterisk)” enables remote

monitoring/ checking data.

First, download the application “KEW Power*(asterisk)” via the internet. Some functions are

available only while connected to the internet. For further detail, please refer to “

8.1. KEW

Power* (asterisk) features

”.

Bluetooth

Tablet device or

Smartphone

www.

.com

[email protected]

1.800.561.8187

Содержание KEW 2062


















































Результаты поиска

Содержание KEW 2062

Отзывы:

Бренды по названию

Популярные бренды

Kyoritsu Electrical Instruments Works KEW 2062, Инструкция по эксплуатации

Результаты поиска

Содержание KEW 2062

Отзывы:

Бренды по названию

Популярные бренды