Kyoritsu Electrical Instruments Works KEW 2062 Скачать руководство пользователя страница 16

Страница: 16 / 49

4.4 Connection to the measured object

KEW 2062/2062BT

- 15 -

KEW 2062/2062BT

DANGER

●

Care should be taken so as not to short-circuit the power line with the metal ends of the

test lead at connection. In addition, do not touch the metal tips.

●

The tips of the current sensor jaws are designed so as not to short-circuit the power line of

the object to be tested but be careful when measuring an un-insulated conductor.

●

Keep your fingers behind the barrier during a measurement.

Barrier: provides protection against electrical shock and ensuring the minimum required

clearance and creepage distances.

For accurate measurement:

●

The declared measurement accuracy is guaranteed where the conductor to be measured

is placed at the center of the current clamp sensor.

●

Care should be taken so as not to pinch the conductors with the tips of the jaws.

●

Confirm and harmonize the wiring configuration of the measurement line and KEW

2062 / KEW2062BT.

● When clamping onto

a conductor, make the arrow mark point towards the load side;

otherwise, polarity of active power (P) will be reversed and displayed.

Arrow mark

● Never clamp two or more conductors.

KEW 2062/2062BT

Chapter 5 Settings

KEW 2062/2062BT

- 16 -

Chapter 5 Settings

Before starting a measurement, adjust the following settings.

* Wiring configuration, frequency of the voltage to be measured,

and VT/ CT ratio, if necessary.

Set the functin switch to “

” to adjust settings.

Note

● Turning the function switch before confirming the altered settings clears all the changes

you made. Confirm the altered settings, and then turn the function switch.

Item selection (Switch the displayed items)

Press the item switching button

[◄►] to toggle the displayed

items and confirm the desired item with the mode button.

Alter the values of each item with the item switching button

[◄►], and

then press the mode button again to confirm the

change. The display returns to the selection screen.

The followings are the default settings. System reset restores the altered changes to the default.

Wiring configuration

VT ratio

CT ratio

Frequency of nominal voltage Backlight

[◄►]

Item switching button

[◄►]

: toggles setting items

Mode button : confirms selection and change.

System reset

Buzzer

www.

.com

[email protected]

1.800.561.8187

Содержание KEW 2062


















































Результаты поиска

Содержание KEW 2062

Отзывы:

Бренды по названию

Популярные бренды

Kyoritsu Electrical Instruments Works KEW 2062, Инструкция по эксплуатации

Результаты поиска

Содержание KEW 2062

Отзывы:

Бренды по названию

Популярные бренды