Kyocera FS-600 Скачать руководство пользователя страница 71

Страница: 71 / 144

Manual Paper Feeding

2-10

Press the

ON LINE/STATUS

key. (The ON LINE/A4 and MANUAL/LGL indicators stop flashing

and stay lit.)

Send printing commands and data from the computer. The DATA/LTR indicator begins flashing.

When the data has processed (the DATA/LTR indicator stays lit), paper is fed from the manual

feed tray.

To exit manual paper feed, press the

FEED/SIZE

key to light the CASSETTE/OTHERS indicator.

Feeding Envelopes

Envelopes should be fed in the face up, right edge first.

Note _____________________________________________________________________

To avoid trouble, we recommend that envelopes are delivered face-up using the face-up tray.

Not all envelopes print well. See

Appendix B

for details on suitable types of envelopes.

Overhead Projection (OHP) Film

To avoid feed problems, OHP film must be fed manually in the manner described above.

Requirements regarding OHP film are also given in

Appendix B

Note _____________________________________________________________________

OHP film must be delivered face-up.

Содержание FS-600

















































































































































Результаты поиска

Содержание FS-600

Отзывы:

Похожие инструкции для FS-600

Бренды по названию

Популярные бренды

Kyocera FS-600, Руководство пользователя

Результаты поиска

Содержание FS-600

Отзывы:

Похожие инструкции для FS-600

Бренды по названию

Популярные бренды