Kyocera Mita KM-1500 Скачать руководство пользователя страница 53

Страница: 53 / 179

2DC

1-4-21

Maintenance

Description

item No.

U244

Checking the DP switches

Description

Displays the status of the switches in the DP.

Purpose

To check if switches in the DP operate correctly.

Method

1. Press the start key. "-S-" appears.
2. Manually turn on and off each switch to check the status. When the on-status of a switch is detected, the

image mode LED corresponding to the operated switch lights.

Image mode LEDs

Description

DP original detection switch

DP timing switch

DP open/close switch

DP original cover switch

: Off,

: On

Completion

Press the stop/clear key. The indication for selecting a maintenance item No. appears.

U252

Setting the destination

Description

Switches the operations and screens of the machine according to the destination.

Purpose

To return the destination setting to its default setting after initializing the backup RAM by running maintenance
item U020.

Method

Press the start key.

Setting

1. Select the destination using the zoom +/– keys.

Display

Description

Inc

Inch (North America) specifications

EUP

Metric (Europe) specifications

ASA

Metric (Asia Pacific) specifications

2. Press the start key. The setting is set, and the machine automatically returns to the same status as when

the power is turned on.

Completion

To exit this maintenance item without changing the current count, press the stop/clear key. The indication for
selecting a maintenance item No. appears.

Содержание KM-1500




















































































































































































Результаты поиска

Содержание KM-1500

Отзывы:

Бренды по названию

Популярные бренды

Kyocera Mita KM-1500, Руководство по обслуживанию

Результаты поиска

Содержание KM-1500

Отзывы:

Бренды по названию

Популярные бренды