Kyocera Mita KM-1500 Скачать руководство пользователя страница 39

Страница: 39 / 179

2DC

1-4-7

Maintenance

Description

item No.

U030

Checking motor operation

Description

Drives each motor.

Purpose

To check the operation of each motor.

Method

1. Press the start key. A selection item appears.
2. Select the motor to be operated using the copy exposure adjustment keys. When selecting the feed motor,

pull out the optional drawer in advance.

Display

Motor

Main motor

Optional feed motor

3. Press the start key. The selected motor operates.
4. To stop operation, press the stop/reset key.

Completion

Press the stop/clear key after operation stops. The indication for selecting a maintenance item No. appears.

U031

Checking sensors for paper conveying

Description

Displays the on-off status of each paper detection sensor on the paper path.

Purpose

To check if the sensors for paper conveying operate correctly.

Method

1. Press the start key.
2. Turn each sensor on and off manually to check the status. When the on-status of a sensor is detected, the

image mode LED corresponding to the operated sensor lights.

Image mode LEDs

Description

Exit sensor

Registration sensor

: Off,

: On

Completion

Press the stop/clear key. The indication for selecting a maintenance item No. appears.

Содержание KM-1500




















































































































































































Результаты поиска

Содержание KM-1500

Отзывы:

Бренды по названию

Популярные бренды

Kyocera Mita KM-1500, Руководство по обслуживанию

Результаты поиска

Содержание KM-1500

Отзывы:

Бренды по названию

Популярные бренды