manualshive.com logo in svg

Kyocera Mita KM-1500, Руководство по обслуживанию, Страница: 48 / 179

Поделиться
Скачать
Kyocera Mita KM-1500 Скачать руководство пользователя страница 48

Maintenance

Description

item No.

2DC

1-4-16

U100

Setting the main high voltage

Description

Performs main charging.

Purpose

Checks the main charging.

Method

1. Press the start key. A selection item appears.
2. Select the item using the cpoy exposure adjustment keys.

Display (copy exposure indicator)

Description

on1 (exp. 1)

Turning the main charger on

on2 (exp. 2)

Turning the main charger on and the laser scanner unit
on and off

3. Press the start key. The selected operation starts.
4. To stop operation, press the stop/clear key.

Test copy mode

While this maintenance item is being performed, copying from an original can be made in test copy mode.

Completion

Press the stop/clear key when main charger output stops while a selection item is displayed. The indication for
selecting a maintenance item No. appears.

U101

Setting the other high voltages

Description

Changes the developing bias clock and the transfer charging output timing.

Purpose

To check the developing bias clock and the transfer charging output timing. Do not change the preset value.

Method

Press the start key. The screen for selecting an item is displayed.

Setting

1. Select the item to be set by lighting a copy exposure indicator using the copy exposure adjustment keys.
2. Change the setting using the zoom +/– keys.

Copy exposure

Description

Setting range

Initial setting

indicator

Exp. 1 (lit)

Developing bias clock frequency

2 to 255

26

Exp. 2 (lit)

Developing bias clock duty

1 to 99

55

Exp. 3 (lit)

Transfer charging output OFF timing

0 to 255

60

Exp. 1 (flashing)

Transfer charging output ON timing

0 to 255

43

3. Press the start key. The value is set.

Completion

Press the stop/clear key while a selection item is displayed. The indication for selecting a maintenance item No.
appears.

Содержание KM-1500




















































































































































































Отзывы:

Нет отзывов