manualshive.com logo in svg

KVH Industries TracVision UHD7, Руководство по установке, Страница: 8 / 41

Поделиться
Скачать
KVH Industries TracVision UHD7 Скачать руководство пользователя страница 8

6

Consider the following TV-Hub installation 
guidelines.

• Select a mounting location in a dry, well-

ventilated area belowdecks away from any 

heat sources or salt spray.

• Do not install the TV-Hub in an area 

surrounded by metal or near any electrical 

devices that emit RF noise.

• The TV-Hub can be mounted horizontally or 

vertically on a flat surface (see Figure 6 and 

Figure 7). 

• Be sure the TV-Hub LED lights will be visible 

to the user. 

• Select a location that will provide adequate 

clearance for the TV-Hub dimensions (see 

Figure 6 and Figure 7). 

• Leave enough room behind the rear panel 

(horizontal mount) or below the rear panel 

(vertical mount) to accommodate connecting 

the cables and making service loops within 

the proper bend radius for strain-relief.

• If you plan to use the TV-Hub’s Wi-Fi 

connections, ensure the TV-Hub mounting 

location provides adequate Wi-Fi reception. 

• If you plan to connect the TV-Hub to the 

vessel’s onboard local area network (LAN), 

choose a location near an available Ethernet 

port.

NOTE: 

A template showing the exact locations of the 

TV-Hub mounting holes and the dimensions between 
them is provided in the Welcome Kit. Installation 
details are provided in 

“Mount the TV-Hub” on 

page 13

.

1.73"

(4.4 cm)

9.34"

(23.7 cm)

7.90"

(20.0 cm)

LED Lights

3.23"

(8.2 cm)

Figure 6:  TV-Hub Dimensions - Horizontal Orientation

Top View

9.34"

(23.7 cm)

11.13"

(28.3 cm)

10.52"

(26.7 cm)

7.90"

(20.0 cm)

LED Lights

Figure 7:  TV-Hub Dimensions - Vertical Orientation

Plan the TV-Hub Installation

3

Содержание TracVision UHD7










































Отзывы:

Нет отзывов