KVH Industries TracVision UHD7 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 41

KVH Industries TracVision UHD7 Скачать руководство пользователя страница 12

10

Follow these steps to remove the shipping
restraints from inside the antenna.

a.

Using a 9/16" nut driver or wrench, remove

the two bolts securing the two shipping

restraint brackets to the frame (see Figure 13).

NOTE:

Be sure to keep the shipping restraint brackets

for future use.

b.

In place of the brackets, place a 3/8" flat

washer (

supplied in kit

) on each of the two

3/8" bolts that you just removed (see

Figure 14). Then reinstall the bolts.

c.

Using cutting pliers, cut and remove the two

tie-wraps equipped with paper tags (see

Once you have removed the restraints, keep

the antenna level as much as possible and

handle the antenna very carefully. Prevent

the internal antenna assembly from rotating

freely within the baseplate to avoid damaging

the limit switch.

IMPORTANT!

Figure 13: Shipping Restraint Bracket Removal

3/8" Bolt (x2)

Lock Nut (x2)

Washer (x2)

Bracket (x2)

Figure 14: Mounting Bolt Reinstallation

3/8" Bolt (x2)

Lock Nut (x2)

Washer (x2)

Washer (x2)

(

supplied in kit

)

Figure 15: Antenna Restraints

Tie-wrap

Tie-wrap

Remove the Shipping Restraints

7

«
...
10
11
12
13
14
...
»

Содержание TracVision UHD7










































Отзывы:

Нет отзывов