KVH Industries TracVision UHD7 Скачать руководство пользователя | Manualshive

Страница: 4 / 41

background image

2

This icon indicates a danger, warning, or caution notice. Be sure to read these carefully to avoid
injury.

WARNING

Risk of Electric Shock

To avoid electric shock, do not open the TV-Hub chassis enclosure. There are no user-serviceable parts
inside.

WARNING

Risk of Electric Shock

If any component of the TracVision system becomes damaged and/or no longer functions normally,
disconnect it from vessel power, secure it from unintended operation, and contact KVH Technical
Support (see

“Technical Support” on page 1

). All repairs or modifications must be performed by a

trained, KVH-certified technician. If you are a KVH-certified technician, you still must contact KVH
Technical Support prior to conducting any repairs or modifications to the equipment.

WARNING

Risk of Explosion

Do not operate the TV-Hub (or any other electrical device) in an environment where flammable gases,
vapors, or dusts are present. In addition, do not operate the TV-Hub in an environment with a
temperature outside its 5º F to 131º F (-15º C to 55º C) temperature range.

WARNING

Risk of Electric Shock

Failure to ground the TracVision system properly to ship’s ground will cause an unsafe floating
ground condition, risking potentially lethal electric shock. See

“Connect Power” on page 21

for details

on the proper grounding of the equipment.

Important Safety Information

«
...
2
3
4
5
6
...
»

Содержание TracVision UHD7










































Отзывы:

Нет отзывов

Похожие инструкции для TracVision UHD7

Бренд: Omron Страницы: 27

Бренд: Clare Controls Страницы: 3

Beacon Station BWS500

Бренд: Vaisala Страницы: 28

Бренд: Opticum Red Страницы: 4

Бренд: cahors Страницы: 50

Tailgater VQ4500

Бренд: KING Страницы: 104

M6060060P1D43602V

Бренд: Ventev Страницы: 2

MATV DAT75HDBOSS

Бренд: Televes Страницы: 2

Бренд: SLX Страницы: 2

Бренд: Phonak Страницы: 16

Бренд: Steren Страницы: 2

DW 3000 One-Way

Бренд: Hughes Страницы: 48

Бренд: A.H. Systems Страницы: 14

FlatWave FL-5000

Бренд: Winegard Страницы: 8

Бренд: Mohu Страницы: 2

TRAV’LER DISH 1000

Бренд: Winegard Страницы: 8

K 51 56 22 /BN 510 386

Бренд: Kathrein Страницы: 3

OBID i-scan ID ISC.ANT.U270/270 FCC

Бренд: Feig Electronic Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды