manualshive.com logo in svg

KVH Industries TracVision UHD7, Руководство по установке, Страница: 33 / 41

Поделиться
Скачать
KVH Industries TracVision UHD7 Скачать руководство пользователя страница 33

31

Before you leave the vessel, test the system to 
ensure the antenna works properly. Fill out the 
Installation Checklist (provided in the Welcome 
Kit) and return it to KVH. Refer to the 
instructions on the form. 
Give the Welcome Kit to the customer, provide 
any passwords and static IP addresses you set 
up, and explain how to use the system. Ensure 
the customer understands the following.

• How to:

• Turn on the system
• Access the web interface
• Interpret TV-Hub status information
• Download software and satellite library

updates (using web interface and/or
mobile app)

• Perform general troubleshooting

• Keep the radome installed on the antenna at

all times. The radome protects the antenna’s
moving parts from wind, rain, and debris.

• The antenna must have a clear view of the

sky to receive satellite TV. Common causes of

blockage include trees, buildings, bridges,

and onboard equipment (see Figure 50).

Heavy rain or snow might also temporarily

interrupt reception.

• Clean the antenna regularly. Dirt buildup on

the radome can affect satellite TV reception.

• You must be located within the satellites’

coverage area to receive TV signals. 

• Please register the system to ensure the best

possible service from KVH. 

CAUTION

In the unlikely event that you need to 

remove the radome, remove power from the 

antenna first because the antenna’s moving 

parts can cause injury.

Figure 50:  Blockage Example

Educate the Customer

22

T

rac

V

ision

Blocked!

Содержание TracVision UHD7










































Отзывы:

Нет отзывов