KVH Industries TracVision UHD7 Скачать руководство пользователя

Страница: 29 / 41

The Setup Wizard appears upon initial startup to
step you through system configuration (see
Figure 45). Before you begin to set up the system:

• Know the service provider and associated

satellite(s)

• Check the latest software version (see below)

• Verify all system components are connected

Update Software and Satellite Library

Before you start the Setup Wizard, update the
system software and satellite library to the latest
versions. Use the Apple

iOS or Android

™

smartphone/tablet mobile app, or follow these
steps to use a laptop PC that has the latest update
files downloaded to it from the KVH Partner
Portal (www.kvh.com/partners).

Select

Exit

in the Setup Wizard page. The web

interface appears.

At the Updates page of the web interface,

select the antenna model. Then select

Install

Update

(see Figure 46). Find the

.kvh

file in

your downloads folder, then double-click to

install.

Wait for the update to complete. It may take

up to 45 minutes. The TV-Hub’s lights will

alternate orange while the update is in

progress. Once complete, the web interface

will report that the latest version is installed.

When the software update is complete, select

the Satellite Library. Then select

Install

Update

. Find the

.xml

file in your downloads

folder, then double-click to install.

Navigate to

Settings

General Settings

and

launch the Setup Wizard.

Select

Proceed with Setup Wizard

Figure 45: Setup Wizard Welcome Page

Figure 46: Software Updates Page

Set Up the System

Содержание TracVision UHD7










































Результаты поиска

Содержание TracVision UHD7

Отзывы:

Похожие инструкции для TracVision UHD7

Бренды по названию

Популярные бренды

KVH Industries TracVision UHD7, Руководство по установке

Результаты поиска

Содержание TracVision UHD7

Отзывы:

Похожие инструкции для TracVision UHD7

Бренды по названию

Популярные бренды