KVH Industries TracVision S3 Скачать руководство пользователя страница 2

Страница: 2 / 81

A Guide to TracVision S3 – ADDENDUM

54-0182 Addendum to Rev. A1

TracVision S3 Owner’s
Manual Addendum

(ECO #5885)

The following information applies to Revision A1 of the
TracVision S3 Owner’s Manual (KVH Part Number 54-0182).

Your TracVision S3 includes four small mounting plates for mounting
the antenna unit on a vehicle. These plates replace the large mounting
plate described in the manual.

1.3

Materials Provided with
TracVision S3

Table 1-3 has been updated to remove the mounting plate.

Component

KVH Part No.

Antenna Unit (comprising):

01-0225-05

†

01-0225-11

††

01-0225-12

†††

01-0225-18

††††

Baseplate Assembly

02-1044-02*
02-1044-04**

Radome Assembly

02-0953-05

RF Cable

32-0589-30

Power Cable

32-0590-30

Antenna Data Cable

32-0630-30

PC Cable

32-0628-06

Kitpack***

72-0101

Owner’s Manual

54-0182

IRD Ground Wire

32-0583-30

Switchplate

02-1023

†

European TracVision S3 system

††

North American TracVision S3 system (defaulted to US DISH Network)

†††

North American TracVision S3 system (defaulted to ExpressVu)

††††

North American TracVision S3 system (defaulted to DIRECTV)

* Baseplate assembly with single-output LNB
** Baseplate assembly with dual-output LNB
*** A complete listing of kitpack contents is provided in

Section 2.2, “Mounting

the Antenna Unit.”

Table 1-3

TracVision S3 Packing List

Cables for the TracVision S3 are
stored beneath the antenna unit
during shipping.

Содержание TracVision S3


















































































Результаты поиска

Содержание TracVision S3

Отзывы:

Похожие инструкции для TracVision S3

Бренды по названию

Популярные бренды

KVH Industries TracVision S3, Руководство пользователя

Результаты поиска

Содержание TracVision S3

Отзывы:

Похожие инструкции для TracVision S3

Бренды по названию

Популярные бренды