KVH Industries TracPhone V11IP Скачать руководство пользователя

Страница: 46 / 55

Gently flare the braid with your fingers (see

Figure 92).

Insert the end of the cable into the connector

body until the dielectric is firmly seated

inside the connector (see Figure 93). Make

sure there is no gap between the knurled end

of the connector and the cable jacket. Also be

sure all braid wires remain on the outside of
the connector.

10.

Trim any excess braid (see Figure 94), if

necessary. The braid should assemble flush to

within 1/16" (1.6 mm) of the connector

shoulder.

11.

Slide the ferrule over the braid until it is flush

against the connector shoulder (see

Figure 95). Make sure there are no exposed

strands of braid with the ferrule in place.

Figure 92: Flaring the Braid

Figure 93: Pushing On the Connector

A common installation failure occurs when

the connector is not seated properly onto the

cable. In these cases, the cable’s center

conductor does not fully engage the electrical

contacts inside the connector. To ensure full

engagement, make certain that there is no gap

between the cable jacket and the knurled end

of the connector before you crimp on the

ferrule. You may need to deburr and center

the end of the conductor to achieve a good fit.

IMPORTANT!

Figure 94: Trimming the Braid

Figure 95: Sliding the Ferrule Over the Braid

Continued

Terminating LMR RF Cables

Appendix

Содержание TracPhone V11IP
























































Результаты поиска

Содержание TracPhone V11IP

Отзывы:

Похожие инструкции для TracPhone V11IP

Бренды по названию

Популярные бренды

KVH Industries TracPhone V11IP, Руководство по установке

Результаты поиска

Содержание TracPhone V11IP

Отзывы:

Похожие инструкции для TracPhone V11IP

Бренды по названию

Популярные бренды