KVH Industries TracPhone V11IP Скачать руководство пользователя

Страница: 40 / 55

ICM Wireless Settings

With Wi-Fi enabled, vessel devices can connect to
the ICM via its built-in wireless access point
(WAP) and receive IP addresses from the ICM
via DHCP (see Figure 75). Follow these steps to
enable and configure the WAP, if desired by the
customer.

NOTE:

The customer may also change the ICM’s

wireless settings at any time at the myKVH web
portal (

www.mykvh.com

At the TracPhone V11-IP web interface, click

the

Settings

tab. Then click

Network

Settings

In Wi-Fi Settings, click

Edit

Set the following wireless options, then click

Save

(see Figure 76):

• State:

Select On.

•

SSID

: Enter a unique name for the vessel

network.

•

Protocol

: Select either 802.11b or 802.11g.

•

Security

: Select either security type –

WPA2 or WEP (128-bit).

•

Password/Passphrase

: If you selected

WPA2, enter a password (between 8-20

characters). If you selected WEP, enter a

passphrase (must be 13 characters).

•

Channel

: Keep the default, or select any

channel for wireless communications.

At the confirmation message, click

Save

Figure 75: Wireless DHCP (Example)

ICM

Mobile
Devices

192.168.5.100

192.168.5.101

Wi-Fi

Establishing a wireless connection onboard a

steel vessel might require a special external

WAP and advanced networking expertise.

IMPORTANT!

Figure 76: Wi-Fi Settings on the ICM

Failure to apply security settings will make

the vessel’s wireless network vulnerable to

outside intrusion.

IMPORTANT!

Continued

Configure the Network

Содержание TracPhone V11IP
























































Результаты поиска

Содержание TracPhone V11IP

Отзывы:

Похожие инструкции для TracPhone V11IP

Бренды по названию

Популярные бренды

KVH Industries TracPhone V11IP, Руководство по установке

Результаты поиска

Содержание TracPhone V11IP

Отзывы:

Похожие инструкции для TracPhone V11IP

Бренды по названию

Популярные бренды