KVH Industries TracPhone V11IP Скачать руководство пользователя

Страница: 20 / 55

Follow these steps to mount the antenna to the
mounting surface.

Position the antenna over the holes drilled in

the mounting surface and make sure the

forward arrow inside the baseplate points

toward the bow and is parallel to the vessel’s
centerline (see Figure 28).

Carefully lower the antenna onto the

mounting surface and ensure the mounting

holes (and foam seals, if used) are aligned.

Using a 7/16" socket/ratchet or nut driver,

unlock the three hex latches securing each of

the antenna’s service hatches (see Figure 19
on page 15). Then gently lower the hatches.

Apply a thin layer of the supplied anti-seize

lubricant to the threads of the four supplied

1/2"-13 mounting bolts to prevent galling.

At each of the four antenna mounting holes,

place a 1/2" flat washer on a 1/2"-13 bolt and

insert the bolt into the hole from above (see

Figure 29).

Secure each mounting bolt to the mounting

surface using a 1/2" flat washer and a 1/2"-13

lock nut from below (see Figure 29).

Tighten the mounting bolts in a cross pattern

until the four rubber feet on the baseplate are

bottomed against the mounting surface. KVH

recommends that you tighten the nuts to

between 35 and 40 ft-lbs (47 and 54 N-m) of

torque.

CAUTION

Be sure to observe the safe handling

instructions in the Material Safety Data Sheet

(MSDS) provided with the anti-seize

lubricant.

Cable Connectors

(Face Stern)

Forward Arrow

Inside Baseplate

(Point Toward Bow)

Hatch

FOR

Antenna

(Top View)

Figure 28: Forward Arrow in Antenna Baseplate

If the foam seals are used, do not reposition

the antenna laterally once the antenna’s foam

seal has made contact with the foam seal on

the mounting surface. If you need to

reposition the antenna, lift the antenna first to

avoid damage to the foam seals.

IMPORTANT!

1/2"-13 Bolt (x4)

1/2" Flat
Washer (x4)

Rubber

Foot (x4)

Mounting

Surface

1/2" Flat
Washer (x4)

1/2"-13 Lock
Nut (x4)

Antenna

Baseplate

Isolation
Bushing (x4)

(preinstalled)

IMPORTANT!
Apply anti-seize
to threads

Foam Seals

(if used)

Stationary

Plate

Figure 29: Mounting the Antenna (Side View)

Mount the Antenna

Содержание TracPhone V11IP
























































Результаты поиска

Содержание TracPhone V11IP

Отзывы:

Похожие инструкции для TracPhone V11IP

Бренды по названию

Популярные бренды

KVH Industries TracPhone V11IP, Руководство по установке

Результаты поиска

Содержание TracPhone V11IP

Отзывы:

Похожие инструкции для TracPhone V11IP

Бренды по названию

Популярные бренды