KVH Industries TracPhone V11IP Скачать руководство пользователя

Страница: 24 / 55

Follow these steps to wire the belowdecks
equipment (see page 52 for a complete wiring
diagram).

Connect the Antenna Data Cable

Connect the antenna data cable to the

supplied 16-position terminal strip connector
as shown in Figure 40.

Place the terminal strip connector into the

base of the supplied cable shroud as shown in

Figure 41.

Secure the end of the data cable to the base of

the shroud using the supplied clamp. This

clamp will help relieve stress on the cable.

Secure the clamp in place with the two

screws.

Carefully fit all of the data cable’s wires

within the base of the shroud.

Snap the shroud’s cover onto the base. Be

sure not to pinch any wires between the cover

and the base.

Plug the terminal strip connector into the rear

panel of the ICM.

Connect the data cable’s ground wire

(attached to the grounding sleeve) to the

ground screw on the rear panel of the ICM

(see Figure 40).

ICM

Antenna

Terminal Strip Connector

13 14 15 16

Blue/White

White/Blue

Brown/White

White/Gray

Gray/White

White/Orange

Orange/White

White/Brown

Red

Black

Orange/Red

Red/Orange

Green/White

White/Green

Green/Red

Red/Green

Grounding
Sleeve

Figure 40: Antenna Data Cable Wiring

The diagram refers to wires by

body color/

stripe color

. For example, “Brown/White”

means the brown wire with white stripe.

IMPORTANT!

Data Cable

Clamp

Terminal Strip Connector

Cover

Base

Figure 41: Data Cable Shroud

Wire the ICM

Содержание TracPhone V11IP
























































Результаты поиска

Содержание TracPhone V11IP

Отзывы:

Похожие инструкции для TracPhone V11IP

Бренды по названию

Популярные бренды

KVH Industries TracPhone V11IP, Руководство по установке

Результаты поиска

Содержание TracPhone V11IP

Отзывы:

Похожие инструкции для TracPhone V11IP

Бренды по названию

Популярные бренды