Flowmate Control FMC
OPERATING INSTRUCTIONS
14
If live parts or wires are damaged, short circuits can result. Therefore, the energy
supply wire must always be equipped with a 30 A fuse. Without properly fusing, a
fire can be caused by a short-circuit!
§2.2.2 Assembling the speed sensor
If a sensor with a counting ring is selected for the speed measurement, it should be attached to a
non-driven wheel as far as possible. If an added appliance is used, the parts are fitted to the inside
of the front right wheel of the tractor.
If a trailer with a spray computer is ordered, the speed sensor with the counting ring is assembled
in the factory. In this case, the system merely needs to be calibrated (see paragraph Ҥ5.10 on
page 41).
Proceed as follows when assembling the counting ring:
•
To start with, the wheel (5) to which the counting ring (6) is to be fitted is dismantled (fig. 4).
•
Push the drilling template (7) over the four long screws of the counting ring (6) and align the ring
centrically to the edge of the rim, to the hub opening and to other circular shapes of the wheel
with the help of the circles on the drilling template. This can be done both on the outside and
also on the inside of the wheel (fig. 4).
•
Then the bores (8) are marked, centred and drilled with a 10.5 mm drill (fig. 4).
•
Screw the ring on the inside of the wheel and attach the spacers (9) between the ring and the
rim. Check whether the ring has been aligned precisely parallel to the rim (fig. 5).
N.B.:
Longer spacers are needed for trailed sprayers.
•
After this, fit the wheel back onto the tractor or sprayer.
Note:
In most four-wheel driven tractors, the speed sensor can often be fitted to the cardan shaft
without problems by means of a self-made holder. The sensor can react to protruding
metal parts on this shaft (hose clamps or welded-on nuts). The counting ring then does
not need to be dismantled!
Содержание Electrical Control EC
