Kuppersbusch KD 3700.0 Скачать руководство пользователя страница 12

Страница: 12 / 18

Service Manual

For internal use only

7.1

Changing the halogen lamp

If the lighting does not work the lamps will firstly need to be checked and you will need to make sure that
the control switch on the control panel of the hood has not developed a fault.

The hood must be disconnected from the mains power supply before it is cleaned or be-
fore any maintenance work is carried out.

Proceed as follows to replace a lamp or lamp mounting:

Open the cover by levering it off at the corresponding
slits.

Replace with a new lamp of the same type.

ATTENTION:

Never touch a new lamp with your bare
hands.

Check the functioning.

7.2

Replacing the entire lamp block

Disconnect the connection of the lamp block that is
to be replaced.

Press the two clips on the side and take out the lamp
block.

Fig. 1

Fig. 2

Fig. 3

Содержание KD 3700.0



















Результаты поиска

Содержание KD 3700.0

Отзывы:

Похожие инструкции для KD 3700.0

Бренды по названию

Популярные бренды

Kuppersbusch KD 3700.0, Руководство по обслуживанию

Результаты поиска

Содержание KD 3700.0

Отзывы:

Похожие инструкции для KD 3700.0

Бренды по названию

Популярные бренды