Kubota KBC26-RS Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 28

Kubota KBC26-RS Скачать руководство пользователя страница 7

＿

6

＿

Connecting Throttle Cable and Stop Switch Wires

1. Insert the throttle cable through the carburetor bracket, then

screw a cable adjuster sleeve into the carburetor bracket fully.

2. Position the slotted fitting on the carburetor so the recessed

hole for the cable lug is away from the cable adjuster sleeve.

3. Rotate the carburetor throttle cam and slip the throttle cable

through the slot in the slotted fitting, making sure the cable lug

drops into the recessed hole.

4. Operate the throttle trigger a few times to make sure that it

works correctly.

5. Adjust the cable adjuster sleeve so the stop on the carburetor

throttle cam just contacts the throttle stop and the cable posi-

tion keep 1-2mm play between cable lug and slotted fittings

when the throttle trigger is fully depressed.

6. When the throttle cable is adjusted correctly, tighten the lock-

nut.

7. Plug the stop switch wires into the matching connectors from

the engine. Note that wire polarity is not important.

Throttle Cable

1-2mm Play

Stop Switch Wires

Cable Lug

Carburetor

Bracket

Slotted Fitting

Lock Nut

Recessed Hole

Cable Adjuster Sleeve

«
...
5
6
7
8
9
...
»

Содержание KBC26-RS





























Отзывы:

Нет отзывов