background image

_

 11 

_

WARNING

DANGER

POTENTIAL HAZARD

 

Petrol contains gasses that can build up pressure inside a fuel tank.

WHAT CAN HAPPEN

 ・

Fuel can be sprayed on you when removing fuel tank cap.

HOW TO AVOID THE HAZARD

 

Remove fuel tank cap slowly to avoid injury from fuel spray.

Before Operation

Oil and Fuel

1. Mix and pour fuel outdoors and where there are no sparks or flames.

2. Always shut off the engine before refueling. Never remove the Trimmer/Brushcutter fuel tank cap while 

the engine is running or immediately after stopping the engine.

3. Always open the fuel tank cap slowly to release any possible 

pressure inside the tank.

4. Do not overfill the fuel tank. Stop filling 10mm from the top of 

the tank.

5. Tighten the fuel tank cap carefully but firmly after refilling.

6. Wipe up any spilled fuel before starting the engine.

7. Move the Trimmer/Brushcutter at least 3m (10ft.) away from 

the fueling location and fuel storage container before start-

ing the engine.

POTENTIAL HAZARD

 ・

In certain conditions petrol is extremely flammable and highly explosive.

WHAT CAN HAPPEN

 ・

A fire or explosion from petrol can burn you, others and cause property

 

damage.

HOW TO AVOID THE HAZARD

 ・

Use a funnel and fill the fuel tank outdoors, in an open area, when the engine is cold.

   

Wipe up any petrol that spills.

 ・

Do not fill the fuel tank completely. Add petrol to the fuel tank until the level is 10mm below 

   the bottom of the filler neck. This empty space in the tank allows petrol to expand.

 ・ 

Never  smoke  when  handling  petrol,  and  stay  away  from  an  open  flame  with  petrol  in  an 

approved container and keep it out of the reach of children.

 ・

Do not mix fuel for more than two month use.

3m(10ft.) 

Minimum

Содержание KBC26-RS





























Отзывы: