manualshive.com logo in svg

Kubota K008-5, Руководство по эксплуатации

Поделиться
Скачать
Kubota K008-5 Скачать руководство пользователя страница 2

W9215-8135-1

06/2021

Dear valued customer,

please fill in the form below. Your information will help us to help you.

These operating instructions only apply to KUBOTA excavators K008-5 and U10-5, which comply with the 
following EC declaration of conformity (page 7).

In addition, the machine’s product identification number must correspond to the following scope of appli-
cation.

K008-5

- Valid from serial number 10001

U10-5

- Valid from serial number 10001

The serial number is part of the product identification number (page 46).

Please contact your KUBOTA dealer for any additional information or troubleshooting procedures not mentioned 
in these operating instructions.

We would also like to point out that the contents of these operating instructions are not part of any previously ex-
isting agreement, commitment or legal relationship nor do they constitute an amendment this. All responsibilities 
are taken from the respective sales contract, which contains the complete and exclusively valid contractual war-
ranty, refer to the "Duties, liability and warranty" section (page 13). This documentation neither extends nor re-
stricts the contractual warranty.

KUBOTA Baumaschinen GmbH reserves the right to change the information contained in this document with re-
spect to future technical development without altering the basic characteristics of the excavators described herein 
and without amending this document.

Distribution and reproduction of this documentation and disclosure of its content are not allowed unless express 
consent is given by the manufacturer. Violators of the above terms are liable for compensation for damages.

Type:

Year of construction:

Product identification number:

Shipment date:

Содержание K008-5









































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды